1977 Chevrolet Monte Carlo Landau on 2040-cars

Auto blog

2016 Chevy Camaro performance figures released

If you want to make a car faster, there are two sure-fire ways to get the job done – add power and/or reduce weight. Chevy has done both for the 2016 Camaro, putting as much as 455 horsepower into its muscle coupe and shaving a few hundred pounds from every trim. That range-topping power comes courtesy of a 6.2-liter V8 engine, and it's enough grunt to push an automatic-equipped Camaro SS to 60 miles per hour in just 4.0 seconds flat (4.3 seconds with a manual) and down the quarter mile in 12.3 seconds at 116 mph (12.5 at 115 for the stick). Not coincidentally, those acceleration specs, at least on paper, put the V8-powered Camaro SS just above the Mustang GT on the muscle-car pecking order. When the road gets twisty, Chevy claims the Camaro SS can generate as much as .97 g on the skidpad. And, thanks in part to its Goodyear Eagle F1 summer tires, the SS can stop from 60 in as little as 117 feet. We look forward to finding out how nimble the new Camaro feels when compared to its primary competitors. <p>Your browser does not support iframes.</p> Moving down one notch to the 335-hp 3.6-liter V6, properly equipped 2016 Camaro coupes can hit 60 in as few as 5.1 seconds and cover the quarter in 13.5 at 103. Perhaps even more intriguingly, the 2.0-liter turbocharged four-cylinder and its 275 horsepower (the only configuration quicker with a manual transmission, incidentally) can propel the Camaro to 60 in 5.4 seconds and through the 'ol 1320 in 14 seconds flat. That's seriously quick, but buyers comparing the Camaro to the Mustang will find that the EcoBoost 2.3-liter is a bit more powerful (310 hp and 320 lb-ft) and quicker (5.1 seconds to 60). Chevy is making lots of noise about the efforts its engineers went through to shed weight from the 2016 Camaro, going so far as to shave down suspension bolts so that no thread went unthreaded. The weight-saving obsession pays off – base Camaro models are down 390 pounds while the SS model drops 223 pounds over the 2015. The 2016 Camaro SS boasts a power-to-weight ratio of 8.1 lbs per pony, a 14-percent improvement over the last-gen. Even though weight is down, chassis stiffness is said to be up by 28 percent over the fifth-gen Camaro coupe. Also of note: The Camaro is now lighter than the Mustang across the board when comparing like-to-like configuration levels. The 2016 Chevy Camaro starts at $26,695 (including $995 for destination).

Callaway rolls out radical Corvette C7 GT3-R at Hockenheim

Leave it to Callaway to take a badass Corvette and make it even more so. Case in point: the new Callaway Corvette C7 GT3-R you see here. It made its big debut this past weekend during the season finale for the ADAC GT Masters series at the legendary Hockenheimring – the on-again, off-again home of the German Grand Prix. Why in Germany, you ask? Because that's where Callaway Competition is based. The racing division got its start in Heilbronn as Woeher & Ciccone back in 1985. It joined with US-based Callaway Cars in 1988 to distribute its modified Corvettes in Europe, and branched out into constructing racing cars in 1994. And this is its latest project. Designed in partnership between Callaway Competition in Germany and Canadian designer Paul Deutschman, the new GT3-R replaces the previous C6-based Z06.R GT3. It packs a 6.2-liter V8 pumping 600 horsepower through an X-Trac six-speed sequential gearbox. And as you can see, it sure looks the part. Callaway will be offering the new GT3-R to privateer teams for entry in a variety of racing series around the world. But it'll also be fielding the example you see here, sponsored by Whelen Engineering that – like Callaway Cars – is based in Connecticut. Callaway Corvette C7 GT3-R World Debut at Hockenheim October 3, 2015 Hockenheim, Germany – October 3, 2015 – This weekend's ADAC GT Masters Season Finale was the backdrop for the unveiling of Callaway Competition's new Callaway Corvette C7 GT3-R. Following a brief presentation to media and invited guests, the successor of the C6-based Callaway Z06.R GT3 was displayed to the public for the first time on October 3, 2015 at the Hockenheimring in Germany. Constructors of GT race cars since 1990 and based in Leingarten Germany, Callaway Competition possesses a wealth of experience, technical know-how and a broad network of specialized professional partners. These elements were crucial to conduct such a large undertaking. After nearly two years of comprehensive planning, intensive development and expert fabrication of vehicle components, Callaway Competition completed the first C7 GT3-R just a few weeks ago. Its striking design comes as a result of the collaboration between Canadian designer Paul Deutschman and team owners Giovanni Ciccone and Ernst Wohr. Mike Gramke, Uwe Hoffmann, Florian Mohring and Andre Zanke were also heavily involved in the vehicle's development.

GM to cut production at 5 plants in North America, kill several models

DETROIT/WASHINGTON — General Motors Co said on Monday it will cut production of slow-selling models and slash its North American workforce in the face of a stagnant market for traditional gas-powered sedans, shifting more investment to electric and autonomous vehicles. The announcement is the biggest restructuring in North America for the U.S. No. 1 carmaker since its bankruptcy a decade ago. GM said it will take pre-tax charges of $3 billion to $3.8 billion to pay for the cutbacks, but expects the actions to improve annual free cash flow by $6 billion by the end of 2020. GM plans to halt production next year at three assembly plants: Lordstown, Ohio, Hamtramck, Michigan, and Oshawa, Ontario. The company also plans to stop building several models now assembled at those plants, including the Chevrolet Cruze, the Cadillac CT6 and the Buick LaCrosse, the sources said. Sources said the Chevrolet Volt, Impala and Cadillac XTS would also be discontinued. Signs of the demise of six passenger-car models have been swirling since July. Plants in Baltimore, Maryland, and Warren, Michigan, that assemble powertrain components have no products assigned to them after 2019 and thus are at risk of closure, the company said. It will also close two factories outside North America, but did not identify those plants. The AP reported that 14,700 jobs would be affected. Some 8,100 of those would be white-collar jobs reduced through buyouts or layoffs. The No. 1 U.S. automaker signaled the latest belt-tightening in late October when it offered buyouts to 50,000 salaried employees in North America. The company also said it will cut executive ranks by 25 per cent to "streamline decision making." Some 6,000 factory workers could lose their jobs or be transferred to other plants. Its shares were last up 6.2 percent at $38.16. Tariff 'headwinds' and cost-cutting GM Chief Executive Officer Mary Barra told reporters on Monday the company can reduce annual capital spending by $1.5 billion and increase investment in electric and autonomous vehicles and connected vehicle technology because it has largely completed investing in new generations of trucks and sport utility vehicles. Some 75 percent of its global sales will come from just five vehicle architectures by early in the 2020s. It plans to reduce annual capital spending to $7 billion by 2020 from an average of $8.5 billion a year during the 2017-2019 period.