2005 Chevrolet Impala Base Sedan 4-door 3.8l Police Vehicle on 2040-cars

Auto blog

Ringbrothers drops more hints about its wild SEMA creations

Ringbrothers isn't finished teasing its SEMA creations. First we got a sliver of rear quarter on a 1969 Chevrolet Camaro that revealed a bundle of carbon fiber and SEMA-obligatory deep-dish wheels. The Wisconsin tuner's now announced its litter of cars headed to the show and a few specs, along with two shadowy drawings. The Camaro, christened with the name Valkyrja and a two-tone paint job, gets stretched in two directions with severe fender flares to widen the body and an extended wheelbase. We're not sure what's happening with the Camaro's snout in the drawing, but under that bulging hood we'll find a 416-cubic-inch LS V8 from Wegner Motorsports. Wegner built the 416-cu-in supercharged LS3 V8 that powered Ringbrothers' 1,000-hp G-Code Camaro in 2016.  The second member of the gang is a 1969 Ford Mustang Mach 1 dubbed Unkl. The exterior begs for attention with a deep blue sea paint job, deep front chin spoiler, bulging hood, yellow brake calipers, and what looks like a racing number inside a roundel on the doors. Unkl gets its motivation from a 520-cu-in Boss V8 built by Kaase Racing Engines, rumored to throw about 800 hp.    Finally, Ringbrothers is bringing its Cadillac Madam V for another Las Vegas go-round after giving the custom coupe some updates. The Madam V is a 1948 Cadillac Series 62 fastback coupe body placed atop an ATS-V chassis, first shown in 2016. The firm didn't elaborate on the changes, so all we can expect for now are the coupe's postwar good looks mixed with new-millennium engineering, and a 3.6-liter twin-turbo V6 with 464 hp under that exceptionally long hood.    For any in attendance at the show, the Valkyrja Camaro debuts at the BASF booth on Tuesday, Nov. 5, 2019 at 9:30 a.m., the Unkl Mustang gets revealed a couple hours later at the Flowmaster/Holley booth, and the Madam V Cadillac will be on display throughout the show at the Ringbrothers booth.

2016 Chevrolet Camaro powers up, slims down

Don't be fooled by its familiar appearance, the 2016 Chevrolet Camaro is vastly different than its iconic predecessors. It has a new chassis, a fresh engine lineup, and is loaded with clever technologies that promise to invigorate and improve the sixth generation of Chevy's legendary sports car. It was revealed Saturday before a crowd of enthusiastic Camaro revelers on Belle Isle in Detroit. Redesigning the sports coupe was a heady task, especially as its archrivals, the Ford Mustang and Dodge Challenger, drive better and are more powerful than ever. But the new Camaro is aiming to be the best combination of handling and raw performance, with quick acceleration and competitive fuel economy. "Redesigning the Camaro is thrilling and challenging all at once, but the secret is to offer something more," Mark Reuss, General Motors executive vice president of product development, said in a statement. It all began with a weight-loss plan. The new Camaro shed more than 200 pounds compared with the outgoing car, with 133 pounds coming from a lighter body-in-white. Then engineers culled weight nearly everywhere, using aluminum for the instrumental panel frame and some suspension components to trim as much fat as possible. The slimmer body rests on new bones. The Camaro's rear-wheel-drive platform is lighter and stiffer in a bid to improve handling. It's a modified version of the underpinnings used by the Cadillac ATS, though about 70 percent of the architecture is unique to the Camaro. Chevy said structural rigidity is improved by 28 percent. As you'll see, healthy doses of Cadillac and Corvette technologies have been used to bolster the Camaro's drive character and performance. The new car is also expected to handle better thanks to a slightly smaller footprint. It is about two inches shorter in length, with most of that due to the more compact wheelbase. It's also an inch shorter in height and an inch slimmer in width. So yes, the Camaro will be leaner, but it will still be plenty mean. The Camaro SS tops the range (for now) with the Corvette's 6.2-liter V8 pushing put 455 horsepower and 455 pound-feet of torque. Known as the LT1, is has a cast aluminum block and cast aluminum cylinder heads, and it's fortified with direct injection, variable valve timing, and cylinder deactivation. About 20 percent of the engine's parts are said to be unique to the Camaro, including the exhaust manifolds.

Looking back at the Citation IV concept that likely shaped the GM EV1

Those who forget history are condemned to repeat it. We're not sure how that applies to the GM EV1, but we'd still like to share something from Autoline Daily, an online automotive new show with our friend John McElroy. He's been covering the business for decades now and recently found something interesting: pictures of the 1984 Chevrolet Citation IV concept, seen above. Displayed half a decade before the first electric concept that would become the EV1 (inset), McElroy says it's now clear that the elegant, aerodynamic EV1 took a lot of styling cues from the Citation IV, which was developed in part thanks to GM's new-at-the-time Aerodynamics Laboratory. We agree with him that the spats over the rear wheels, the flush glass, and the covered headlights all bear a certain kind of similarity between the two cars. That the colors almost match is a nice coincidence. The Impact (the concept version of the EV1) looked "frumpier," McElroy says, because it wasn't as long as the Citation. You can read a lot more about the Citation IV here and check out McElroy's thoughts in the video below. Find the Citation starting at around 3:45. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.