1960 Chevrolet Impala on 2040-cars

Auto blog

2016 Chevy Volt will be available across Canada, unlike most of US [UPDATE]

UPDATE: The story's been updated to add a response from General Motors of Canada. It's not enough that the Toronto Blue Jays may be the most intimidating team in Major League Baseball. Now, it appears that our neighbors to the north will also have some bragging rights in regards to General Motors' Chevrolet Volt extended-range plug-in vehicle. Specifically, most of Canada will have access to the 2016 version before most of the US will. In fact, the car will be available in Canada before people can buy it in Michigan. A trip to Windsor, Ontario, anyone? The Volt, which will boast a longer plug-in range than the current version, could go on sale in Canada as soon as November, GM Authority says. The model's second-generation version may debut in California as soon as this month, and is slated to be sold later this year in the 10 other states that abide by the so-called CARB (California Air Resources Board) rules for zero-missions vehicles. Those states include Oregon, Maine, New York and Massachusetts. But not GM's home state of Michigan. Either way, the new generation model's debut can't come soon enough for the US automaker, as Volt sales in 2015 have seriously lagged the 2014 numbers because of people waiting for the new version. "We will receive the 2016 Volt in Canada this fall, starting with our key Volt markets in Quebec, Ontario and British Columbia," wrote General Motors of Canada spokesman George George Saratlic in an e-mail to AutoblogGreen. "Note these are also the three provinces that provide provincial incentives on EV purchases. We'll then roll out Volt to the rest of the country." Last week, details were revealed about the first sales of the 2016 Volt, where marketing efforts will be concentrated among the largest plug-in buying states in the union. The other 39 states will get their shot starting next year with the 2017 model-year variant. Related Video:

2016 Camaro gets most revealing tease yet

Chevrolet started its long teaser campaign for the 2016 Camaro by just revealing the exhaust manifold and front frame, but as time has passed the company has slowly unveiled more. In the latest glimpse ahead of the pony car's May 16 debut, we're actually getting to see the model's profile completely undisguised. As suggested by the recent tease of the rear and hood, the 2016 Camaro wears a sharper, more angular design than the current model. This is especially the case when you look at the taut lines making up the rear. Chevy claims that the new shape underwent 350 hours of wind tunnel tests to be able to generate left lift, improve cooling and reduce wind noise in the cabin. A smooth underbody pan is among the aerodynamic tweaks, and it runs from underneath the front grille to the center of the Camaro. Chevy asserts that all of the changes at the front help reduce lift by 30 percent. Related VIdeo: 2016 Camaro is all about the Aero Total aerodynamic lift improved by 30 percent for improved stability 2015-05-11 DETROIT – After 350 hours of wind tunnel testing – often 24 hours a day – the new Camaro will slip more easily through the wind, and drivers of the Camaro SS will experience a marked improvement in reduced aerodynamic lift. These changes illustrate the lengths the aerodynamics team went to for improved performance, stability, cooling and lower wind noise intrusion "The importance of aerodynamics increases exponentially as we increase vehicle performance," said Kirk Bennion, Exterior Design manager. "As engine output increases, we need more engine cooling. As acceleration and top speeds climb, we need to reduce lift for better high-speed stability. However, we cannot make any changes at the expense of increasing drag, which can hurt fuel economy. "To balance these different aerodynamic targets, we tested literally hundreds of changes on the new Camaro, millimeters at a time." For example, the initial design called for the lower grille bars to be set at a 20-degree angle to the horizon. However, after meticulous testing, the team improved engine-cooling airflow by 1 percent by shifting the angle to 13 degrees – a change that achieved the airflow target while maintaining the original grille design. And rather than a traditional front air dam to reduce aerodynamic lift, the team developed a flush belly pan that stretches from the front grille to the center of the vehicle.

GM extends production cuts, affects Cadillacs, Camaro and Acadia

General Motors is extending production cuts at some of its North America factories due to a chip shortage that has roiled the global automotive industry, the U.S. carmaker said on Thursday. The move's impact has been baked into GM's prior forecast that the shortage could shave up to $2 billion off this year's profit. GM's Lansing Grand River assembly in Michigan will extend its downtime through the week of April 26. The plant makes Chevrolet Camaros and Cadillac CT4 and CT5 sedans. It has been out of action since March 15. GM's Spring Hill assembly in Tennessee will shut down for two weeks starting the week of April 12. The plant makes the Cadillac XT5, XT6 and GMC Acadia. The company said it has not taken downtime or reduced shifts at any of its more profitable full-size truck or full-size SUV plants due to the shortage. The news was first reported by CNBC. Reporting by Ankit Ajmera in Bengaluru; Editing by Maju Samuel and Sriraj Kalluvila