Truecar Certified Dealer Gm Military And Warehouse Club Discounts Welcome on 2040-cars

Auto blog

2016 Camaro gets most revealing tease yet

Chevrolet started its long teaser campaign for the 2016 Camaro by just revealing the exhaust manifold and front frame, but as time has passed the company has slowly unveiled more. In the latest glimpse ahead of the pony car's May 16 debut, we're actually getting to see the model's profile completely undisguised. As suggested by the recent tease of the rear and hood, the 2016 Camaro wears a sharper, more angular design than the current model. This is especially the case when you look at the taut lines making up the rear. Chevy claims that the new shape underwent 350 hours of wind tunnel tests to be able to generate left lift, improve cooling and reduce wind noise in the cabin. A smooth underbody pan is among the aerodynamic tweaks, and it runs from underneath the front grille to the center of the Camaro. Chevy asserts that all of the changes at the front help reduce lift by 30 percent. Related VIdeo: 2016 Camaro is all about the Aero Total aerodynamic lift improved by 30 percent for improved stability 2015-05-11 DETROIT – After 350 hours of wind tunnel testing – often 24 hours a day – the new Camaro will slip more easily through the wind, and drivers of the Camaro SS will experience a marked improvement in reduced aerodynamic lift. These changes illustrate the lengths the aerodynamics team went to for improved performance, stability, cooling and lower wind noise intrusion "The importance of aerodynamics increases exponentially as we increase vehicle performance," said Kirk Bennion, Exterior Design manager. "As engine output increases, we need more engine cooling. As acceleration and top speeds climb, we need to reduce lift for better high-speed stability. However, we cannot make any changes at the expense of increasing drag, which can hurt fuel economy. "To balance these different aerodynamic targets, we tested literally hundreds of changes on the new Camaro, millimeters at a time." For example, the initial design called for the lower grille bars to be set at a 20-degree angle to the horizon. However, after meticulous testing, the team improved engine-cooling airflow by 1 percent by shifting the angle to 13 degrees – a change that achieved the airflow target while maintaining the original grille design. And rather than a traditional front air dam to reduce aerodynamic lift, the team developed a flush belly pan that stretches from the front grille to the center of the vehicle.

GM recalls select Chevy Cruze, Sonic and Buick Verano models over airbag issue

General Motors is recalling certain 2012 Buick Verano, Chevrolet Cruze and Sonic models due to a defect in the driver's airbag system. According to the National Highway Traffic Safety Administration, the airbag has a shorting bar which may contact two internal terminals. If that happens during a crash, the supplemental restraint may not deploy, increasing the risk of driver injury. The recall includes a total of 2,949 units.
GM will contact owners and replace the steering wheel airbag coil at no cost. At this point, it's unclear when the recall will begin, though owners may contact the automaker at 1-800-521-7300 for more information. You may also take a closer look at the full NHTSA notice below.

Honda, Chevy reveal low-drag speedway aero for Indy 500

As the two automakers currently participating in the IndyCar Series, both Chevy and Honda were invited this year not only to provide engines to the teams on the starting grid, but to develop their own aerodynamics packages as well. Both revealed their designs for the road-course races a few months ago, but with the Indy 500 approaching at break-neck speed, they've now unleashed their aero approaches for speedways. Both are based on the Dallara DW12 chassis introduced to the series a couple of years ago, but sacrifice some of their downforce at the altar of speed. And you can tell as much from looking at them: both Honda (above) and Chevy (below) have streamlined their designs, with single-plane front wings, lower-profile rear wings and fewer winglets on the body and around the wheels in between. The idea is to allow the cars to reach higher top speeds with less drag, while offering the necessary amount of downforce for the banked turns. With the four opening road-course rounds complete, teams using either automaker's equipment will keep the existing aero kits on their cars for the Grand Prix of Indianapolis on the infield course next week, then switch to the speedway package for the Indianapolis 500 later this month. Then it'll be back and forth for the rest of the season as the circus switches between road courses and speedways. Honda Unveils 2015 IndyCar Super Speedway Aero Kit Apr 30, 2015 - SPEEDWAY, Indiana - To be used at the Indianapolis 500 - Manufacturer seeking 11th Indianapolis 500 victory since 2004 - First public running to take place Sunday at Indianapolis Honda today debuted the "Super Speedway" aero kit of aerodynamic upgrades and components its teams will use at this year's 99th running of the Indianapolis 500. The Honda Super Speedway Aero Kit, produced by Honda Performance Development, Honda's racing arm in North America, includes a variety of individual aerodynamic components fitted to the existing Honda-powered Dallara Indy car chassis. All are intended to give Honda's six Indy car teams – encompassing a potential 17 '500' entrants - the ability to maximize performance at the 2.5-mile Indianapolis Motor Speedway oval and other large ovals ( over one mile in length) on the 2015 Verizon IndyCar Series schedule. "We're excited to unveil our Super Speedway aero kit, the newest element in this era of enhanced manufacturer competition in the Verizon IndyCar Series," said Art St. Cyr, president of HPD.