2009 Chevrolet Colorado Lt Automatic 4-door Truck on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Sunday Drive: Tracking Tokyo's top performers

The big news of the week mostly came from Tokyo. All of Japan's biggest automakers made waves at the Motor Show, but the winner of the event has to be Mazda. The big Vision Coupe and little Kai Concept stole the show, won our hearts, and earned a ton of attention for the automaker. We can't wait to see how these two concepts impact the design, engineering, and technology of future production models. Take a look at our mega image gallery post below to see everything in high-resolution glory. Interestingly, the single biggest click-magnet of the 2017 Tokyo Motor Show was the BMW X2. We shouldn't be surprised. Crossovers of all shapes and sizes dominate the American marketplace, and the X2 is clearly the most attractive of BMW's even-numbered, coupe-influenced X models. Plus, it's headed for production, with sales starting in the spring of 2018. Moving past the Tokyo Motor Show, Autoblog readers are apparently very interested in the 2019 Chevy Camaro. Spy shots of just about every iteration of Chevy's muscle car lit up the 'net last week, leaving us very interested in seeing what's hiding behind all that camouflage. As always, tune in to Autoblog next week for a front-row seat to all the happenings worth following in the automotive industry. 2017 Tokyo Motor Show | Mega Gallery Mazda Vision Coupe | Tokyo Motor Show's big, sensuous 4-door Mazda Kai concept hints at a more muscular, refined Mazda3 2018 BMW X2 crossover revealed, adorned in gold and silver 2019 Chevrolet Camaro: 1LT, SS, ZL1 all spied with updated styling

GM reportedly developing 2.5-liter turbo four-cylinder

General Motors is allocating a massive amount of resources to developing electric technology, but it's not forgetting about the gasoline-powered cars that make up the bulk of its sales. It's reportedly designing a new 2.5-liter turbocharged four-cylinder engine based on its 2.7. Citing "sources familiar with the matter," enthusiast website GM Authority wrote that the 2.5-liter four is "in [the] final stages of development," meaning it should be announced sooner rather than later (assuming the report is accurate). Technical details are few and far between as of writing. The publication learned that the 2.5 will be part of the Cylinder Set Strategy (CSS) family of engines and that it will be mechanically related to the 2.7-liter currently found in the Chevrolet Silverado 1500, among several other models. It will feature dual overhead camshafts. It's too early to tell which models the 2.5-liter four-cylinder will end up in, or how much power it will generate. The output will likely depend on the application. For context, the 2.7 delivers 310 horsepower at 5,600 rpm and 348 pound-feet of torque between 1,500 and 4,000 rpm in the Silverado. In the smaller Colorado, it provides anywhere between 237 and 310 horsepower depending on the trim level selected. While this is pure speculation, our crystal ball tells us the engine will end up powering crossovers. It's an easy deduction to make. We can't imagine it will be offered in the Silverado, and seeing it in the Colorado is unlikely because its entry-level engine develops 237 horsepower; there's likely not much of a market for a midsize truck with 200 or so horsepower. Putting it in the Corvette wouldn't make sense and the Camaro has nearly reached the end of its life cycle without a successor planned. This leaves us with Chevrolet's range of crossovers, like the Equinox, as well as their GMC-, Buick-, and Cadillac-branded counterparts. We're not discounting the possibility that the cars set to receive the 2.5 haven't been unveiled, but those are likely crossovers, too; the odds of seeing another big Chevy sedan are very, very low. General Motors hasn't commented on the report, and it hasn't publicly announced plans to expand its CSS family of engines. If the report is accurate, we should learn more about the new turbocharged, 2.5-liter four-cylinder engine in the not-too-distant future. Featured Gallery 2022 Chevrolet Equinox RS View 56 Photos Buick Chevrolet GM GMC