No Reserve! 2010 Chevrolet Cobalt With Very Low Miles! on 2040-cars

Auto blog

This is what a 2017 Chevy Camaro Z28 could look like

The latest Camaro Z28, the enthusiast darling of the somewhat frumpy fifth-generation pony car, only hit the scene in 2014. It housed the wonderful 7.0-liter, naturally-aspirated LS7 small block V8 and featured a ton of aero bits. The trickest pieces may have been the dynamic spool valve shocks, legitimately race tech for the road. So with the new Camaro out in the wild, we were wondering what a new Z28 might look like, and thus, commissioned these renders based on our best guesses as to what a future Z28 might be. Since Chevy didn't stray too far from the Zeta-chassis Camaro formula with its new Alpha-based car, our vision of a new 2017 Camaro Z28 likewise is a sequel rather than a reboot. The exterior styling and aero details are similar, but sleeker. The defining and protruding front splitter is back, but it's smoothed slightly and better integrated. It shares quad exhaust pipes with the lowlier SS, but they're of the beveled Z06 variety, and sized up to a howitzer caliber. Instead of a weak faux rear fender vent, our version gains a real brake cooling duct. Some iconic elements, like the hood extractor vent and the large decklid spoiler, remain. What we can't see, we have to speculate on. As the track-focused, hardcore pony car in the Camaro lineup, the Z28 will have to do battle with the Ford Shelby Mustang GT350R. There's simply no avoiding it. And whereas Ford distinguished that car with a 5.2-liter, 526-horsepower, flat-plane-crank V8, Chevy is likely to look to the parts bin to find motivation. This isn't a knock; the LS and LT-series small block V8s are both numerous and power-dense. And there's one engine that seems to do the trick: the LSA, last seen in the old CTS-V and still on sale in the Camaro ZL1 (and of course, still being produced as a crate engine). In ZL1 form, the LSA makes about 580 hp, which is a nice margin over the GT350R. It's also a high-zoot but not top-of-the-line mill, having been mostly superseded by the 650-hp LT4. That puts our probable Z28 far enough behind the new CTS-V and current Corvette Z06 in the pecking order to be a safe bet, without hobbling it with the LT1 shared with the Camaro SS and regular Corvette. Will those trick spool-valve shocks from Multimatic make it to the Z28 again? Ford is taking the GT350R very seriously, and if the expensive but supremely capable suspension system is required to manhandle the Shelby at the track, you can bet that Chevy will pony up for it.

2016 Camaro gets most revealing tease yet

Chevrolet started its long teaser campaign for the 2016 Camaro by just revealing the exhaust manifold and front frame, but as time has passed the company has slowly unveiled more. In the latest glimpse ahead of the pony car's May 16 debut, we're actually getting to see the model's profile completely undisguised. As suggested by the recent tease of the rear and hood, the 2016 Camaro wears a sharper, more angular design than the current model. This is especially the case when you look at the taut lines making up the rear. Chevy claims that the new shape underwent 350 hours of wind tunnel tests to be able to generate left lift, improve cooling and reduce wind noise in the cabin. A smooth underbody pan is among the aerodynamic tweaks, and it runs from underneath the front grille to the center of the Camaro. Chevy asserts that all of the changes at the front help reduce lift by 30 percent. Related VIdeo: 2016 Camaro is all about the Aero Total aerodynamic lift improved by 30 percent for improved stability 2015-05-11 DETROIT – After 350 hours of wind tunnel testing – often 24 hours a day – the new Camaro will slip more easily through the wind, and drivers of the Camaro SS will experience a marked improvement in reduced aerodynamic lift. These changes illustrate the lengths the aerodynamics team went to for improved performance, stability, cooling and lower wind noise intrusion "The importance of aerodynamics increases exponentially as we increase vehicle performance," said Kirk Bennion, Exterior Design manager. "As engine output increases, we need more engine cooling. As acceleration and top speeds climb, we need to reduce lift for better high-speed stability. However, we cannot make any changes at the expense of increasing drag, which can hurt fuel economy. "To balance these different aerodynamic targets, we tested literally hundreds of changes on the new Camaro, millimeters at a time." For example, the initial design called for the lower grille bars to be set at a 20-degree angle to the horizon. However, after meticulous testing, the team improved engine-cooling airflow by 1 percent by shifting the angle to 13 degrees – a change that achieved the airflow target while maintaining the original grille design. And rather than a traditional front air dam to reduce aerodynamic lift, the team developed a flush belly pan that stretches from the front grille to the center of the vehicle.

GM's Oshawa plant may close after Camaro production moves

Most of the time, when vehicle production is moved from one assembly plant to another, it spells bad news for the former. While General Motors won't go so far as to say its Oshawa, Ontario factory, which is losing the Chevrolet Camaro to the Lansing Grand River plant, is in trouble, analysts seem to think the factory's days are numbered. Forecasts for the facility are far from positive. The loss of the Camaro this year, combined with GM's targeted shutdown of a single-shift assembly line responsible for the fleet-only Chevy Impala Limited and the Equinox crossover is a bad enough omen. But with AutoForecast Solutions CEO Joe McCabe telling The Detroit News that the plant's other two products, the Cadillac XTS and Buick Regal, aren't likely to stick around beyond 2017, things look decidedly grim at Oshawa. "There is a fairly strong chance that the plant could close," Jeff Schuster, senior VP of forecasting for LMC Automotive, told The Detroit News. That doesn't mean that Unifor, Canada's auto union, and the Canadian government are going to let the factory die without a fight. And with the latter chipping in $10 billion as part of GM's 2009 bailout, you might think it has a degree of leverage in the situation. A meeting between the government and the Detroit Three at the 2015 North American International Auto Show revealed that Oshawa is already a topic of conversation. "We made it very clear that we would like to see an indication on the future of Oshawa sooner, in particular because the timing is very challenging for our supply chain to be able to adjust to potentially future orders or changes, but also to know that there are going to be future opportunities at Oshawa," Ontario's Minister of Economic, Development, Employment and Infrastructure Brad Duguid told The Detroit News. "Bottom line: It's time they made a longer-term commitment here," Unifor President Jerry Dias said, echoing Duguid's statements. It's unclear if this sort of strong talk will be enough to save 3,300-plus employees, although based on the analysts' forecasts, we doubt it.