1971 Chevrolet C-10 Colorado Truck! 350 Automatic 400 Trans Runs Great! Chevy on 2040-cars

Auto blog

NHTSA upgrades probe into 1.7 million GM vehicles over wiper failures

WASHINGTON — The U.S. National Highway Traffic Safety Administration (NHTSA) said Tuesday it is upgrading an investigation into 1.7 million General Motors vehicles for windshield wiper failures. The auto safety agency opened the probe in November 2018 to see if GM needed to expand a 2016 recall of 2013 model year Chevrolet Equinox and GMC Terrain SUVs to cover additional vehicles. The engineering analysis probe covers 2010-2012 and 2014-2016 Equinox and Terrain vehicles. NHTSA could demand a recall after it completes the probe. NHTSA said it has reviewed 1,900 complaints and reports related to the issue in the 1.7 million vehicles. NHTSA said it has seen elevated failure rates in the 1.7 million vehicles, even though GM said the recalled vehicles have "double the warranty rate and five times the complaint rate." GM said it will "fully cooperate to support their investigation. We do not believe these windshield washer systems are defective." The wiper failures that prompted the 2016 recall were attributed to water and debris intrusion into the windshield wiper assembly ball joints, leading to excessive wear and eventual detachment of the ball joint. GM said it was installing an improved windshield wiper motor and transmission assembly and relocating a drain hole at the base of the windshield. Related Video:

Fernando Alonso sputters in his Indy test

INDIANAPOLIS — Helio Castroneves and Fernando Alonso kept waiting around Wednesday. Now both international stars have some unfinished business to take care before qualifying for this year's Indianapolis 500. After enduring a rain delay of more than four hours then watching IndyCar regulars turn laps at Indianapolis Motor Speedway for two more hours, Castroneves and Alonso finally made it onto the track — but couldn't quite complete their refresher course. "Happy to be back here because this place is great," Alonso said after posting a fast lap of 218.690 mph — the slowest of the nine-driver evening session. "We were slow because the weather and some of the decisions people made on running time and things like that." He faced a bevy of problems in his first trip back to Indy since an impressive rookie performance in 2017. The rain delay forced organizers into rescheduling the one-day test, moving the rookie and refresher driver time from midday to the evening, cutting a significant amount of practice time for Alonso and the others. And when the green flag finally waved, Alonso's No. 66 car stalled in the warmup lane forcing the two-time Formula One champion from Spain to be towed back to pit lane where his crew worked feverishly to fix an electrical problem while sat in the cockpit. Eventually, he did get out and passed the first of two refresher phases. He'll have to wait until opening practice of the 500 on May 14 to pass the second. "It was frustrating for everyone because it was a brand new chassis and a brand new car, so we expected to run a lot," said Alonso, who drives for McLaren Racing. "If we could have had this at midday, you could work on your issues in the afternoon and then go out again." To put his day in perspective, Takuma Sato, the 2017 Indy winner from Japan, posted the fastest lap of the day at 226.993 mph and Colton Herta was the fastest rookie at 226.108. Castroneves, as usual, was good right from the start and posted a fast lap of 225.565. The three-time Indianapolis 500 winner looked smooth and fast on his favorite track and wasted no time passing the first phase. That much should have been expected from the popular Brazilian, who has recorded seven top-three finishes in 18 Indy starts and will make his season debut May 11 in the IndyCar Grand Prix. The weather and yellow flags prevented four of the five veterans — Castroneves, Alonso, Oriol Servia and JR Hildebrand — from passing phase two. Only Indy native Conor Daly made it.

Our favorite mid-engine Corvette theories and rumors

The mid-engine Corvette! We just saw blurry photos through the foliage, and are hearts are all aflutter because it means that this car is real. And it's the most " never before" Corvette since 1984. Which leads us to all kinds of wacky theories and speculation. Everybody knows something or heard from a guy. None of those guys (or gals) from GM are talking to Autoblog, to be clear. But that won't stop us from stirring the pot. Let's go over a few point-by-point. The pushrod engine will be replaced by an overhead-cam V8 Car and Driver has repeatedly reported that an overhead-cam engine will come after the mid-engine Corvette's debut with an old-school pushrod. We've heard the same thing firsthand, albeit from a source with no connection to the development of the Corvette or powertrain. "At some point two valves can't pass future emissions regulations," said the guy we know. While the pushrod engine is compact, the design makes it difficult - if not impossible - for sophisticated variable valve timing (and lift) systems that control combustion with more precision. Hasty conclusion: The pushrod engine has a finite life in front of it. This one's a lock, it's a just a matter of when. Bowling Green's new paint shop is really the mid-engine assembly line Credit to Reddit for this one. Like we said, everybody knows a guy. But let's look deeper. The new paint facility costs $439 million dollars and adds 450,000 square feet, almost half the size of the existing plant. Plus GM announced another $290 million in upgrades at Bowling Green Assembly. That sure sounds like a lot of money, but you can actually spend that much on a paint booth. Porsche spent 500 million Euros (about $561 million dollars) to add the Macan assembly to its Leipzig, Germany plant in 2014. Chrysler shelled out $850 million for a paint shop in Sterling Heights, Michigan. GM spent $600 million for a new paint shop at the Fairfax (Kansas City) plant. Honda, on the other hand, is working on a thrifty $210 million project in Marysville, Ohio that includes a 300,000 square foot expansion, and the low-volume Acura NSX facility only cost $70 million. Hasty conclusion: The square footage and cost could easily mean a new assembly line instead of (or in addition to) a paint line. And if the NSX plant was really that cheap, GM could have hidden a similar sum in its existing announcements.