1972 Chevrolet Chevelle on 2040-cars

Auto blog

Common Dodge Ram 1500 vs. Chevrolet Silverado breakdowns

These two trucks are famous for their ability to get the job done. Still, even the toughest vehicle can have mechanical problems at some time. What if we match the Dodge Ram 1500 and Chevrolet Silverado head to head? Let's find out more about common repairs for each model. Also, learn some tricks to pay for car repairs. Clunky Steering Both Dodge and the Chevy owners sometimes notice bumping and clunking when steering. This might be more noticeable when driving over bumps. The cause is usually different in each truck though. In the Dodge Ram, clunky steering is more likely due to a defective lower ball joint. Replacement costs around $300 - $400, parts and labor. Clunky Chevy Silverado steering is probably a steering rack failure. This problem appears more often in trucks with over 90,000 miles. Silverado steering rack repair will run you up to $1,000 or more. Starting Woes For the Chevy Silverado with over 130,000 miles, you might notice trouble starting. This problem may appear occasionally at first, but it typically gets worse. Excluding a weak battery, the culprit is usually the starter. Replacement will cost you around $330 - $500. Of the total cost, $90 is for labor only. Now the Dodge Ram might make a ticking sound when starting, especially on models with over 94,500 miles. The noise often disappears after the engine warms up. These symptoms may indicate a broken exhaust manifold. Repair costs range from $800 - $900. Burning Oil & Gas Gauge On The Blink Sometimes, the Dodge Ram burns oil much faster than normal. In models with over 125,000 miles, this often points towards a leaky intake manifold gasket. A knocking sound may also appear with acceleration along with possible engine misfire. The cost to repair is around $200 - $300. The Chevy Silverado has its own surprises, especially when you've filled the gas tank but the gauge still reads low. Or the needle fluctuates widely from low to full while driving. In trucks with over 120,000 miles, it's likely due to a faulty fuel sensor. You might need a full fuel pump replacement, which can cost you up to $820, parts and labor. Water Inside And Poor Heat The Ram 1500 rear window has been known to leak. You might notice the back seat and floor wet after a rainstorm. This is more common in trucks with over 65,000 miles. Resealing the Ram 1500 rear window costs around $150 - $250.

Honda, Chevy reveal low-drag speedway aero for Indy 500

As the two automakers currently participating in the IndyCar Series, both Chevy and Honda were invited this year not only to provide engines to the teams on the starting grid, but to develop their own aerodynamics packages as well. Both revealed their designs for the road-course races a few months ago, but with the Indy 500 approaching at break-neck speed, they've now unleashed their aero approaches for speedways. Both are based on the Dallara DW12 chassis introduced to the series a couple of years ago, but sacrifice some of their downforce at the altar of speed. And you can tell as much from looking at them: both Honda (above) and Chevy (below) have streamlined their designs, with single-plane front wings, lower-profile rear wings and fewer winglets on the body and around the wheels in between. The idea is to allow the cars to reach higher top speeds with less drag, while offering the necessary amount of downforce for the banked turns. With the four opening road-course rounds complete, teams using either automaker's equipment will keep the existing aero kits on their cars for the Grand Prix of Indianapolis on the infield course next week, then switch to the speedway package for the Indianapolis 500 later this month. Then it'll be back and forth for the rest of the season as the circus switches between road courses and speedways. Honda Unveils 2015 IndyCar Super Speedway Aero Kit Apr 30, 2015 - SPEEDWAY, Indiana - To be used at the Indianapolis 500 - Manufacturer seeking 11th Indianapolis 500 victory since 2004 - First public running to take place Sunday at Indianapolis Honda today debuted the "Super Speedway" aero kit of aerodynamic upgrades and components its teams will use at this year's 99th running of the Indianapolis 500. The Honda Super Speedway Aero Kit, produced by Honda Performance Development, Honda's racing arm in North America, includes a variety of individual aerodynamic components fitted to the existing Honda-powered Dallara Indy car chassis. All are intended to give Honda's six Indy car teams – encompassing a potential 17 '500' entrants - the ability to maximize performance at the 2.5-mile Indianapolis Motor Speedway oval and other large ovals ( over one mile in length) on the 2015 Verizon IndyCar Series schedule. "We're excited to unveil our Super Speedway aero kit, the newest element in this era of enhanced manufacturer competition in the Verizon IndyCar Series," said Art St. Cyr, president of HPD.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck