1971 Chevelle Ss on 2040-cars

Auto blog

400,000 Chevy, GMC pickups recalled: Side airbags can explode

DETROIT — General Motors is recalling more than 400,000 pickup trucks in the U.S. because the side airbags can explode without warning and spew parts into the cabin. The recall covers certain 2015 and 2016 Chevrolet Silverado and GMC Sierra 1500, 2500, and 3500 trucks. Documents posted Friday by U.S. safety regulators say the airbag inflator can rupture or the end cap can fly off on both sides of the trucks. Documents say three inflators ruptured in 2015 Silverados last month, one in Florida and two in Texas. All three trucks were unoccupied at the time, and GM says it has no reports of injuries. Dealers will replace both side airbag modules. The company says it has a limited number of replacement parts available. Owners will be notified starting Aug. 16 and they'll get a second letter when parts are widely available. About 9,000 of the trucks were recalled last year for the same problem. The company says a manufacturing defect allowed moisture into the inflator while it was being manufactured, causing corrosion. The inflators were made in Mexico by Joyson Safety Systems, the company that took over Takata. Back in April, Silverado and Sierra were among nearly 750,000 GM vehicles in a National Highway Traffic Safety Administration (NHTSA) investigation into non-deploying driver-side airbags. That investigation is ongoing. Takata is responsible for the largest recalls in automotive history, covering about 100 million inflators among 19 major automakers worldwide, including about 67 million inflators in the United States. Nineteen deaths in the U.S. have been attributed to Takata inflators. Only about 50 million of the 67 million recalled inflators in the U.S. have been repaired. This latest recall is a good reminder to go to NHTSA's recalls website and enter your car's VIN. Millions of recalled vehicles still pose a danger to their owners. Yours could be one of them.   Recalls Chevrolet GM GMC airbag Takata airbag recall

GM reintroduces Tripower name in the worst way possible

The story of General Motors' use of the Tripower moniker begins way back in 1957, when Semon E. "Bunkie" Knudsen, then General Manager of GM's Pontiac division, directed his engineers to inject more performance into his brand's line of V8-powered automobiles. Fuel injection was an option, but hot rodders flocked instead to Tri-Power (marketed way back when with a hyphen), which grafted a trio of two-barrel Rochester carburetors onto a single intake manifold. A legend was born. And that legend was born of performance. At idle and when full power wasn't required, Pontiac's Tri-Power system used just the middle carburetor, which helped make the setup easier to tune. Depending on the year and model, either a vacuum system or a mechanical linkage opened up the two outer carbs, thereby switching from two barrels to six, and allowing the engine to take in more fuel and air. And it was an easy marketing win – six barrels is better than four barrels, right? Because performance! So, when news filtered in that GM has resurrected the Tripower name, those of us who grew up attending classic car shows and wrenching on old Pontiacs did a double-take. And then we all collectively sighed. Turns out that today's Tripower refers to a trio of fuel-saving measures that include cylinder deactivation, active thermal management, and intake valve lift control, according to Automotive News. And, at least for now, it applies to GM's line of fullsize trucks powered by a 2.7-liter turbocharged four-cylinder engine. We're all for saving fuel whenever possible. And we have zero say in how any automaker chooses to market its products and technologies. But, we'll offer our two cents anyway: Relaunching a storied name from the past is fine. Relaunching a storied name from the past while completely overlooking the reasons the name got famous in the first place is only going to irritate the people who remember the name in the first place. Couldn't they just call this new technology package something else? Related Video: News Source: Automotive NewsImage Credit: Getty Green Marketing/Advertising Chevrolet GM Pontiac Automotive History Truck chevrolet silverado

Experimental mid-engine XP-819 Corvette going up for auction

It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.