1977 Chevrolet Camaro Sport Coupe on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

General Motors reportedly considering small electric pickup

General Motors is considering adding a small entry-level model to its range of electric pickups, according to a recent report. The carmaker is currently showing a prototype to a select group of customers to gather feedback about the model before executives decide its fate. Industry trade journal Automotive News claims that it saw the pickup during a workshop organized by General Motors and describes it as being "smaller than the Ford Maverick and the Hyundai Santa Cruz." For context, the Maverick stretches about 200 inches long, 73 inches wide, and 69 inches tall, so it's around 12 inches shorter, 11 inches narrower, and 10 inches lower than the recently-unveiled Chevrolet Colorado. It sounds like this little GM truck would be closer in size to the Brazilian-market Chevy Montana, pictured at top. But unlike the Montana, the model that Automotive News got a look at had two doors, a "low roofline," a four- to four-and-a-half-foot cargo box, and a design described as futuristic and sporty. If launched, the yet-unnamed pickup would be marketed as an "affordable" EV with a base price pegged under $30,000. However, that's a big if: the pickup — whose name hasn't been announced — hasn't been approved for production. "We're creating these to get a reaction and then to try to modify it or move on," Michael Pevovar, the director affordable EV and crossover design for Chevrolet, told the publication. "The input may come back that it's just too small, and that's okay," he added. If it turns out to be too small for buyers, General Motors hasn't ruled out building its entry-level electric pickup on a different architecture to make it a little bigger. It's too early to tell where the electric pickup would slot in the General Motors portfolio if executives approve it. Chevrolet immediately comes to mind, especially considering the sub-$30,000 price point. The model would make more sense with a bowtie on its front end than with a Cadillac emblem, GMC's trucks are normally positioned higher than Chevrolet's, and Buick hasn't built a pickup in many decades. Similarly, there's no word on when it would enter production or where it would be built. With that being said, there's very clearly a market for affordable, small pickup trucks. As of the third quarter of last year, Ford had sold more Mavericks than it had the Expedition or the Ranger. Hyundai hasn't sold as many Santa Cruz trucks, but it's still not too shabby, having beaten out the Venue and Accent last year.

GM to sink over $900M into 4 plants, mostly for a new V8

FLINT, Mich. — General Motors says it will spend more than $900 million to update four factories, with the bulk going to an engine plant in Flint, Michigan, to build the next-generation V8 for big pickup trucks and SUVs. Factories in Rochester, New York; Defiance, Ohio; and Bay City, Michigan, also will see investments, some to make V8 engine components as well as parts for future electric vehicles, the company said Friday. The investments won't create any new jobs, but they will preserve about 2,400 hourly and salaried positions positions at the four sites, the company said. The investments “provide job security at these plants for years to come,” Gerald Johnson, GM's manufacturing chief, said in a statement. Much of the money, $579 million, will go to Flint Engine Operations for equipment to build the sixth-generation small-block V8 that will go into the next round of big pickup trucks and SUVs. The plant now employs about 700 people who also will keep making their current product, a diesel engine used in light trucks. GM, like other automakers, is facing stricter government fuel economy standards and pollution limits starting in the 2024 model year. New vehicles sold in the U.S. will have to average at least 40 miles per gallon of gasoline in 2026, up from about 28 mpg, under new Biden administration rules that undo a rollback of standards enacted under former President Donald Trump. That means the new V8 will have to get better mileage and pollute less than the current versions. Although GM wouldn't release details on the new engine, Johnson said during a news conference at the Flint plant that it would be more efficient than the current version. GM has a goal of selling only electric passenger vehicles by 2035, but Johnson said that's a dozen years out, a period when many customers will still want gas engines. “We know that has a horizon,” he said. “Between here and there, there are a lot of internal combustion customers that we don't want to lose,” he said. In addition to Flint, GM's engine components plant in Bay City, Michigan, will get $216 million to build camshafts and connecting rods, and to machine engine blocks and heads for the new V8 being built in Flint. The plant now employs about 425. The Defiance, Ohio, foundry will get $55 million to build a variety of block castings for the new V8. Included is $8 million for castings to support future electric vehicles, the company said. The plant has about 530 employees.