1985 Chevy K20 Commercial Utility Cargo Vehicle Cucv 1010 20567 Miles on 2040-cars

Auto blog

Chevrolet Silverado, GMC Sierra could get independent rear suspension

The Chevrolet Silverado and the GMC Sierra could reportedly receive a variant of the four-link independent rear suspension found under the new Tahoe and Suburban. While that's not a surprise, a recent report suggests electrification, not comfort, convinced General Motors to make the change. Replacing the time-tested solid rear axle with an independent suspension will improve comfort, handling and off-road prowess, while adding weight, and likely making the trucks a little bit more expensive. It's a fair trade-off, but GM Authority learned the real reason for the swap is that at least one of the pickups will spawn an electric model, and it's more difficult to package a bulky battery pack around a solid rear axle. The independent rear suspension takes up far less space, even if it has more moving parts. General Motors will build its first regular-production electric pickup on an evolution of the Silverado's T1 platform named BT1, according to the same source. The b stands for -- you guessed it -- batteries. The firm reportedly doesn't want to make two suspensions for cost reasons, so the independent setup will come standard regardless of whether the truck runs on gasoline, diesel, or electricity. As a bonus, Chevrolet and GMC could choose to offer their T1-based trucks with Magnetic Ride Control or an air suspension, options available on the 2021 Suburban and Tahoe. The independent rear suspension will also find its way to the next-generation GMC Yukon due to be revealed January 14, and to the 2021 Cadillac Escalade scheduled to make its debut February 4. The long-rumored, born-again Hummer will get it, too, because it will arrive as an electric model built on the BT1 platform. It's worth noting none of this is official, and General Motors has remained quiet about what's next for its new suspension design, and what will be under its electric truck's sheet metal. If the GM Authority report is accurate, the Silverado (pictured) and the Sierra could ditch their solid rear axle for the 2021 model year. The change will likely be accompanied by other tweaks inside and out. Featured Gallery 2019 Chevrolet Silverado 1500 View 16 Photos Chevrolet GMC Truck

2016 Camaro gets most revealing tease yet

Chevrolet started its long teaser campaign for the 2016 Camaro by just revealing the exhaust manifold and front frame, but as time has passed the company has slowly unveiled more. In the latest glimpse ahead of the pony car's May 16 debut, we're actually getting to see the model's profile completely undisguised. As suggested by the recent tease of the rear and hood, the 2016 Camaro wears a sharper, more angular design than the current model. This is especially the case when you look at the taut lines making up the rear. Chevy claims that the new shape underwent 350 hours of wind tunnel tests to be able to generate left lift, improve cooling and reduce wind noise in the cabin. A smooth underbody pan is among the aerodynamic tweaks, and it runs from underneath the front grille to the center of the Camaro. Chevy asserts that all of the changes at the front help reduce lift by 30 percent. Related VIdeo: 2016 Camaro is all about the Aero Total aerodynamic lift improved by 30 percent for improved stability 2015-05-11 DETROIT – After 350 hours of wind tunnel testing – often 24 hours a day – the new Camaro will slip more easily through the wind, and drivers of the Camaro SS will experience a marked improvement in reduced aerodynamic lift. These changes illustrate the lengths the aerodynamics team went to for improved performance, stability, cooling and lower wind noise intrusion "The importance of aerodynamics increases exponentially as we increase vehicle performance," said Kirk Bennion, Exterior Design manager. "As engine output increases, we need more engine cooling. As acceleration and top speeds climb, we need to reduce lift for better high-speed stability. However, we cannot make any changes at the expense of increasing drag, which can hurt fuel economy. "To balance these different aerodynamic targets, we tested literally hundreds of changes on the new Camaro, millimeters at a time." For example, the initial design called for the lower grille bars to be set at a 20-degree angle to the horizon. However, after meticulous testing, the team improved engine-cooling airflow by 1 percent by shifting the angle to 13 degrees – a change that achieved the airflow target while maintaining the original grille design. And rather than a traditional front air dam to reduce aerodynamic lift, the team developed a flush belly pan that stretches from the front grille to the center of the vehicle.

Updated Chevy Silverado spied, possibly with aluminum components

Chevrolet is readying a refresh for its trusty Silverado pickup, and these spy shots give us our first glimpse at what might be in store. The front and rear fascias of this prototype are covered, obscuring some styling tweaks (with LED accents up front). More interestingly, our spies suggest that many of the Silverado's body components could move to aluminum with this mid-cycle update. The hood will go from steel to the lighter alloy, and it's possible the front fenders could benefit from the weight-saving material, too. Ford's latest F-150 is extremely aluminum-intensive, and by switching the construction, 700 pounds was trimmed off the truck's weight. We've already heard that General Motors is working with a similar plan for its next-generation fullsize trucks. Beyond that, expect the smaller 5.3-liter V8 to ditch its six-speed automatic transmission in favor of the eight-speed unit that's already mated to the larger, 6.2-liter V8. Neither transmission will stick around very long, as the trucks will likely adopt a 10-speed automatic around 2017. Look for the updated Silverado to debut later this year, likely as a 2016.5 model.