2003 Chevrolet Trailblazer Lt Sport Utility 4-door 4.2l on 2040-cars

Auto blog

Mustang retakes monthly pony car sales crown from Camaro

Going back to their origins in the Swinging '60s, the Ford Mustang and Chevrolet Camaro have been fierce rivals for fans' hearts and dollars. Historically, the Ford often led in volume, but Chevy took the muscle car top spot in 2009 upon the Camaro's rebirth. However, with the launch of the latest Blue Oval pony car, the tide is turning back in Ford's favor. November was the first full month of sales for the new 2015 Mustang, and according to TheDetroitBureau.com, the model did spectacularly well. The Blue Oval shifted 8,728 of them, up 62 percent from same month last year, with the automaker proclaiming it the model's best November sales since 2006. Conversely, 4,385 units of the Camaro were delivered, down 13.5 percent year-over-year, meaning its sales were roughly half that of the new-generation Mustang. Ford is understandably happy with the results, and product development director Raj Nair even hinted to TDB that another version of the Mustang might be unveiled at January's North American International Auto Show. Rumor has it that the model will be the even more potent Shelby Mustang GT350R. Despite the Mustang's November success, the Camaro outsells it year to day. So far in 2014, Ford has sold 73,124 Mustangs versus 79,669 examples of the Camaro. With December offering the last chance for an overtake, the Bowtie may yet remain king for this year's sales crown. A new Camaro is peeking over the horizon, as well. It's reportedly moving to the Alpha platform used by the Cadillac ATS, and production could start in late 2015. Prototypes are already testing at the Nurburgring, and camouflaged examples have been spotted weirdly being compared to its '80s forefather.

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck