White Ls,4x4,dual Air,102k Hwy Miles,boards,tow Pkg,6 Pass,ex-govt, on 2040-cars

Auto blog

Ringbrothers drops more hints about its wild SEMA creations

Ringbrothers isn't finished teasing its SEMA creations. First we got a sliver of rear quarter on a 1969 Chevrolet Camaro that revealed a bundle of carbon fiber and SEMA-obligatory deep-dish wheels. The Wisconsin tuner's now announced its litter of cars headed to the show and a few specs, along with two shadowy drawings. The Camaro, christened with the name Valkyrja and a two-tone paint job, gets stretched in two directions with severe fender flares to widen the body and an extended wheelbase. We're not sure what's happening with the Camaro's snout in the drawing, but under that bulging hood we'll find a 416-cubic-inch LS V8 from Wegner Motorsports. Wegner built the 416-cu-in supercharged LS3 V8 that powered Ringbrothers' 1,000-hp G-Code Camaro in 2016.  The second member of the gang is a 1969 Ford Mustang Mach 1 dubbed Unkl. The exterior begs for attention with a deep blue sea paint job, deep front chin spoiler, bulging hood, yellow brake calipers, and what looks like a racing number inside a roundel on the doors. Unkl gets its motivation from a 520-cu-in Boss V8 built by Kaase Racing Engines, rumored to throw about 800 hp.    Finally, Ringbrothers is bringing its Cadillac Madam V for another Las Vegas go-round after giving the custom coupe some updates. The Madam V is a 1948 Cadillac Series 62 fastback coupe body placed atop an ATS-V chassis, first shown in 2016. The firm didn't elaborate on the changes, so all we can expect for now are the coupe's postwar good looks mixed with new-millennium engineering, and a 3.6-liter twin-turbo V6 with 464 hp under that exceptionally long hood.    For any in attendance at the show, the Valkyrja Camaro debuts at the BASF booth on Tuesday, Nov. 5, 2019 at 9:30 a.m., the Unkl Mustang gets revealed a couple hours later at the Flowmaster/Holley booth, and the Madam V Cadillac will be on display throughout the show at the Ringbrothers booth.

GM exploring ways to raise half-ton Duramax diesel tow rating

Lots of truck owners cheered when GM announced fuel economy numbers for the 2020 Chevrolet Silverado with the 3.0-liter Duramax diesel inline-six. Even after Ram let loose its EPA mileage ratings for the 2020 Ram 1500 EcoDiesel, the Chevy oil-burner still took the trophy. The victory was years in the making, GM engineers spending an entire four-year development cycle refining the LM2 Duramax to increase mileage. The tradeoff, as well all know by now, is towing; the Duramax in half-ton duty pulls a maximum 9,300 pounds in the Silverado. Rivals across town can do more, the Ford F-150 PowerStroke rated at 11,500, the Ram 1500 EcoDiesel game to pull 12,560. GM engineer John Barta told Muscle Cars & Trucks that more hauling chops could be on the way, explaining, "We’re actually looking at upgrading some of the materials around (the engine bay) to see if we can maybe raise our tow rating." Engine bay materials are at issue due to thermal complexities underhood. John Barta, GM's assistant chief engineer of diesel engine controls, said the Duramax's inline-six configuration allowed engineers to get emissions hardware like the combined selective catalytic reduction, diesel oxidation catalysts, and diesel particulate filter unit closer to the engine, where it heats up quicker, getting emissions down quicker. But that filter puts another heat source in those confines, enforcing a cap on the tow rating to keep the engine and other systems from overheating. "If you look under the hood," he said, "youÂ’ll see a significant amount of silver ‘moon tapeÂ’ around to make sure things arenÂ’t getting overheatedÂ… if we were to go up in higher towing, which we can, we start impacting the possibility of deteriorating some of the components.” There isn't much space for more grille, so swapping for a better grade of "moon tape" or a different kind of material could reduce engine bay heat, extracting a higher tow rating in the process.  It's important to note a point Barta's been making for months about the Duramax figures, though. "Even though itÂ’s nice to brag about big numbers, in reality, light duty customers are not towing that large with their trucks," and, "We do know that (95 percent) of our light duty customers donÂ’t tow over 9,000 pounds." On our First Drive of the 2020 Silverado diesel we called out the tow rating, but emphasized that the Chevy and GMC have more important challenges to overcome.

GM laying off more than 4,000 workers Monday morning

According to reports from Automotive News, The Detroit News, and CNN, General Motors plans to begin laying off more than 4,000 salaried workers starting Monday morning. In a statement to AN, a spokesperson for the automaker said, "We are not confirming timing. Our employees are our priority. We will communicate with them first." We've been expecting layoffs at General Motors since November, 2018. At the time, the Detroit-based automaker announced it would seek to shed 8,100 salaried employees, shut down five assembly plants in North America, and kill off several slow-selling models. One month earlier, GM offered buyout packages to 18,000 workers and said it would seek to cut its global workforce by 25 percent. A spokesperson said at the time the moves were "proactive steps to get ahead of the curve by accelerating our efforts to address overall business performance." The cost-cutting moves are expected to save GM up to $2.5 billion in 2019 and as much as $6 billion by 2020. David Kudla, CEO and chief investment strategist of Mainstay Capital Management, referred to the impending culling as "Black Monday" and told The Detroit News that the layoffs would begin around 7:30 a.m. and continue in waves throughout the coming days and weeks. GM plans to deliver on its fourth-quarter and full-year 2018 earnings report on Wednesday. President Donald Trump plans to deliver the annual State of the Union address a day earlier on Tuesday. We expect to hear plenty more from both sides over the next several days.