10 Chevy 3500 Ltz 4x4 Dually Leather Gps Navi Certified Warranty Wefinance Texas on 2040-cars

Auto blog

Buick Encore, Chevy Trax reportedly dead after 2022

The Buick Encore will not get an encore, and the Chevrolet Trax is dead in its tracks. Separate unverified reports say the two crossovers, which are essentially identical underneath the sheetmetal, will retire at the end of the 2022 model year without being directly replaced. Citing anonymous sources, enthusiast website GM Authority wrote that production of the Encore and the Trax is scheduled to end in the third quarter of 2022. Both models are manufactured in Bupyeong-gu, South Korea, and General Motors will reportedly use the extra production capacity to build more examples of the Trailblazer, which outsold the Encore and the Trax combined by a significant margin in 2021. General Motors hasn't commented on the report, but we wouldn't be surprised if the end is indeed near for the Encore and the Trax. Buick released the Encore for the 2013 model year, and Chevrolet launched the Trax for 2015, but the model made its debut as the Opel Mokka in 2012. It's at the end of its life cycle, and sales figures reflect this: 20,072 units of the Encore were sold in America in 2021, a drop of 52% compared to 2020, while 42,590 examples of the Trax found a home, a 60% decline. It's further proof that Americans don't like small cars. Viewed in that light, the decision not to replace either crossover makes perfect sense. If the report is accurate, the Encore GX (which is not related to the Encore in any way) will enter the 2023 model year as Buick's entry-level model. The situation is a little more complicated at Chevrolet: The pocket-sized Spark is on its way out in 2022 as well, meaning that the Trailblazer will become the entry point into the range. It's a different story in Europe: Opel, which is now part of the Stellantis group, released the second-generation Mokka in June 2020.

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

The 2021 F-150 elevates Ford's bed game

The new 2021 Ford F-150 is ushering in a new era of pickup capability, but there's more to it than the introduction of the PowerBoost hybrid. While that new powertrain is certainly the truck's headlining element, the supporting electrical architecture enables a level of utility that hasn't been offered in past consumer half-tons. The true party trick is Ford's new "Pro Power Onboard" feature, which is essentially a built-in generator that provides juice for the 2021 F-150's rather robust in-bed power station. This system is available even on gasoline-engine models, but its utility is maximized with the electrified powertrain. ICE models equipped with the option max out at 2.0 kilowatts, while the PowerBoost hybrid can be had with either a 2.4- or a whopping 7.2-kilowatt inverter.  The idea here is that the F-150 can essentially stand in for a high-output portable generator. In a worksite example provided by Ford, a PowerBoost model with the 7.2-kW upgrade and a single tank of fuel could provide 32 hours of power for an 1,800-watt compound miter saw, a 1,000W circular saw, a 1,200W battery charger, a 1,200W hammer drill, and a 1,000W air compressor with hundreds of watts to spare for lighting and other accessories. But even without the Pro Power Onboard option, Ford's new bed setup enables more versatility than in previous models. The new Tailgate Work Surface option adds a flat work area with integrated rulers, recesses for pencils or small tools, and even a stand for a personal device.  Ford is neither the first to offer an auxiliary power outlet in a half-ton pickup bed, nor was Ford the first to introduce a more feature-rich tailgate. GMC's MultiPro tailgate was a major innovation on that front, and while it is geared mostly toward improving the cargo utility of the bed, it can also be customized with 12-volt power and even an accessory speaker system. The Ram 1500 is also offered with both a multi-function tailgate and AC power in the bed, though the latter option is limited to models with the RamBox cargo package.  As half-ton pickups approach levels of towing and hauling capability that begin to blur lines with heavy-duty offerings, it's clear that automakers are looking for ways to differentiate themselves without stepping on their own bigger trucks' toes. These new bed and tailgate innovations may yet be the tip of the iceberg when it comes to full-size pickup versatility. Related Video: