Chevrolet Silverado 1500 on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Corvette Stolen In Detroit Returned To Owner After 33 Years

A Detroit man had his stolen Corvette returned 33 years after it disappeared while parked on one of Detroit's main drags, according to ABC 7. The last time George Talley saw his 1979 Corvette was on a July day in 1981, when it disappeared from its parking spot on Jefferson Avenue in Detroit. He had given up hope of ever seeing his car again, until a phone call from AAA brought his sporty ride home. Authorities had come across a Corvette with a questionable VIN in Hattiesburg, Mississippi. When they ran the number Talley's stolen car report came up. The car is still in pretty good shape and only has 47,000 miles on the odometer. Talley wasn't sure how he could get the car back home, but General Motors stepped in and agreed to cover the cost of bringing the 'Vette home. Talley has always had a passion for Detroit-made muscle cars. "I've always liked Corvettes. It was attractive. The ladies like 'em," Talley told ABC 7.

Basic configurator for 2021 Chevy Colorado and GMC Canyon slips online

TFLnow discovered basic configurators for the 2021 Chevrolet Colorado and GMC Canyon are already online at GM's site for employee discounts. These aren't the fully-featured whiz-bang configurators that will show on the retail websites soon, but they include a bunch of the relevant info a shopper would be looking for. After trim changes detailed earlier this year, the 2021 Colorado offers the most choice, even with the two-door base model gone. Cutting the entry-level Colorado also means the entry-level price has gone up by $3,900; the 2020 Colorado could be had for $22,495, but the 2021 model starts at $26,395 after the $1,195 destination charge. That gets you the extended cab with a standard bed in two-wheel drive. The 2WD crew cab with a short bed starts at $28,295, and the 2WD crew cab with a standard bed starts at $30,595. At the top end, the ZR2 model runs $44,395, which is $200 more than the 2020 version. The color palette isn't complete, but the options page shows a number of choices for packages. The Redline Special Edition Package goes up $10 to $2,690, the Tonneau and Step Package increase $100 to $1,195, a new Chrome Package puts shiny stuff in places like the door handles and steps for $300, while the Black Bowtie Emblem Package drops $80 to $140. The one-inch front leveling kit, which was thought to cost $150 based on early order information GM Authority had seen, is here listed for $450 and available on the Colorado but not the Canyon.  The Canyon makes matters a tad simpler by having many options locked in depending on which one starts with — 2WD Elevation Standard starting at $27,595, 2WD Elevation for $31,195, 4WD AT4 with a cloth interior for $39,395 or AT4 with leather for $41,195, the least expensive Denali starting at $42,095 for a crew cab short box with 2WD. The Elevation includes items like the Convenience Package that are options on the base model, and also offers a $1,400 High Elevation Package conferring heated and power black leather seats, plus a heated steering wheel, that can't be optioned on the Elevation Standard. The pinnacle is the crew cab with a standard bed in Denali 4WD trim for $45,895. Colors and many of the final options and accessories, such as the AT4 Off-Road Performance Edition Package we've heard about, are also missing here, but there's heaps to play around with to get an idea of what you'll be in for if you're considering a 2021 Canyon. Related Video: