Heated Auto Power Convertible 6.0l V8 Bank Financing 2007 2005 2006 Ssr Ls Red on 2040-cars

Auto blog

New Chevrolet Silverado to be revealed on Facebook on Thursday

There's not much to see here, but if you're one of those waiting for the reveal of the 2014 Chevrolet Silverado 1500, above is the teaser image that Chevrolet posted on its Facebook page. We've seen the truck in form-fitting camo before, and even less can be made out here beyond those seriously punchy Silverado-esque fenders and the knowledge that the projector-beam headlamps teased previously do indeed work. We'll have to wait until Thursday for a full perusal of the "bold exterior design" and "careful attention given to every detail" we've been promised.
Gathering intel and rumors, magnesium and aluminum contribute to the Silverado's weight loss plan, the purported "High Country" top-tier trim will contribute to luxury pickup truck competition and profit margins and the next-generation small-block V8 will contribute to improved fuel economy. On the engine note, there have been rumors of available V6 engines, and when Facebook user John Jones asked "Where's your answer to that EcoBoost Chevy?", the Bowtie replied "stay tuned on the 13th. We think you'll be pleased...".
Along with the "Raise the Bar" tag, Chevrolet says of the Silverado, "You asked, we delivered." You can watch the reveal live on Chevrolet's Facebook page at 9:30 am EST, this Thursday, December 13. The GMC Sierra 1500 will also be there, and we'll see both in person at the Detroit Auto Show in January.

More Corvette Stingray Factoids: Vanishing panel gaps and 26-mpg LT1

During January's Detroit Auto Show, we managed a longer than expected wandering tag-team interview with C7 Corvette chief engineering exec Tadge Juechter (pictured above), and LT1 engine boss Jordan Lee (pictured below). They are, quite honestly, two of the very nicest bigshot lads to ever walk the engineering corridors of an American manufacturer. Both are enthralled by what they're doing for a day job. So are we.
We've followed the pre-sale anticipation for the Chevrolet C7 Corvette Stingray like an Oreck vacuum yanking every speck of dirt from a well-trampled carpet. Everything is reportable and contains a grain of further knowledge about this dramatically important and cheered-for car, as it continues to be pressured into representing all that is superior about the American dream. The Corvette wears one heavy cloak.
So, most of what was talked about has been expertly reported already right here on Autoblog. But, looking through our notes again, both Jeuchter and Lee added facts to the buzzing mix.

GM patent reveals new two-stage turbocharger

Modern turbochargers may be some of the best ever made, but performance is something that engineers are always trying to improve. According to GM Inside News, General Motors (GM) is hoping to alleviate some of the negative aspects of a two-stage turbocharger setup with a newly-patented design. The patent, that was filed on May 19, 2016, reveals a clever bypass system that allows the engine, a four-cylinder unit, to optimize both the low-pressure and high-pressure inlets for its respective functions. According to the filing, a conventional two-stage turbocharger setup is engineered to allow both turbines to operate simultaneously at low and mid engine speeds. At high engine speeds, only the low-pressure turbine works. The setup can't isolate either the low or high pressure side, which can impair low-end performance. GM's new two-stage turbocharger setup looks to eliminate this by linking the high-pressure turbo to the exhaust manifold through the high-pressure inlet duct. The low-pressure turbo is attached to the high-pressure turbo by a low-pressure inlet duct, which is linked to a connecting channel. A single actuator that is housed in the exhaust manifold creates a bypass that can opens the high-pressure inlet or close the connecting channel. Depending on what the engine load and speed is, the ECU guides the actuator—a single rotating spindle with discs corresponding to flanges on the high and low pressure sides—to isolate one of the two turbos. Isolating the turbos allow the respective inlets to be engineered for the best possible fluid dynamic performance. The setup should increase performance and decrease lag. There's no word on what car this setup will make an appearance on, but it will most likely be used in premium vehicles before trickling down to the rest of GM's vehicles. Related Video: News Source: GM Inside News, AutoGuide via GM Authority Cadillac Chevrolet GM Technology Sedan turbo patent engine turbocharging