1953 Chevrolet Truck Hot Rod on 2040-cars

Auto blog

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.

Weekly Recap: BMW rolls out ambitious plug-in hybrid electric plan

"We believe that for the United States, this is going to be very important." – Julian Arguelles Let there be no doubt, BMW is serious about electric vehicles. The German automaker said this week it will make plug-in hybrid versions of all of its core models, an aggressive move that demonstrates its commitment to electric propulsion systems. BMW did not specify which vehicles will get the plug-in systems or provide a timeline for when they will arrive. But the announcement is clearly more than blustering, and the company revealed a 3 Series plug-in prototype this week at an event in France. BMW said the 3 Series uses a version of its 2.0-liter turbocharged four-cylinder engine (240 horsepower, 300 pound feet of torque) with an electric motor sandwiched between the engine and transmission in place of the torque converter. It has an all-electric range of 22 miles. A plug-in X5 with the same powertrain was also displayed alongside the 3 Series, though the X5 has been on the auto-show circuit for more than a year, including a recent stop in Los Angeles. Those two vehicles use "eDrive," and BMW's plans represent the first widespread transfer of its technology from development of the i3 and i8 models to more mainstream products. BMW said it's developing electric powertrains so they can be deployed rapidly across its range, and they are flexible enough to be used with fuel cells in future products. Enticingly, BMW is also working on a "Power eDrive" system, which debuted in a 5 Series GT concept at the event in France. This setup has two electric motors powered by a 20-kilowatt-hour battery pack, and when teamed with a four-cylinder turbo, pump out about 670 hp. Reinforcing BMW's commitment, the company will add more than 200 jobs at its factory in Dingolfing, Germany, to support electric-vehicle development. The moves come as BMW and other automakers diversify their portfolios while fuel economy and emissions regulations are getting tighter around the world. The United States has set a 54.5-mpg CAFE requirement for the 2025 model year. BMW said the electric vehicles were developed with an eye toward the US market, its government policies and its wide-ranging commuting styles. "We believe that for the United States, this is going to be very important," spokesman Julian Arguelles said. Ben Scott, a senior analyst in London with automotive research firm IHS, said BMW's moves are expensive – but necessary – to keep pace with the market.

Chevy Trax engineer says GMC version possible

The Buick Encore is doing so well and its platform-mate the Chevrolet Trax has such good reviewer vibes going for it already, that a GMC version hasn't been ruled out. During the recent press launch, Automotive News asked lead engineer Al Manzor if the Trax could wear a GMC-branded suit, to which Manzor replied, "I think that is certainly possible." That's a long way from telling us anything about the probability of a GMC version of the Trax, and a legion of questions would need to be answered before it could happen. How would a GMC version be priced to leave room for the $26,465 GMC Terrain but not eat into sales of the $20,995 Trax or the $24,035 Encore? Or would that matter? Could it primarily be considered to encourage a new faction of The Yukon Set at the compact end, GMC buyers being famously committed to the marque? And of course, would there be a Denali version? It'll probably be a long while before we have any kind of answers, but if you want to see it happen, the door to your campaign of persuasion is at least ajar.