1951 Chevy Dump Truck Flat Bed on 2040-cars

Auto blog

Even if GM does close all 5 of those plants, it'll still have too many

DETROIT — General Motors' monumental announcement on Monday that it will close three car assembly plants and two powertrain plants in North America and slash its workforce will only partially close the gap between capacity and demand for the automaker's sedans, according to a Reuters analysis of industry production and capacity data. Sales of traditional passenger cars in North America have been declining for the past six years and are still withering. After GM ends production next year at factories in Michigan, Ohio and Ontario, it will still have four U.S. passenger-car plants — all operating at less than 50 percent of rated capacity, according to figures supplied by LMC Automotive. In comparison, Detroit-based rivals Ford and Fiat Chrysler Automobiles will have one car plant each in North America after 2019. The Detroit Three are facing rapidly dwindling demand for traditional passenger cars from U.S. consumers, many of whom have shifted to crossovers and trucks. Passenger cars accounted for 48 percent of retail light-vehicle sales in the United States in 2014, according to market researchers at J.D. Power and Associates. This year, sedans will account for less than a third of light vehicle sales. That shift in turn has left most North American car plants operating far below their rated capacities, while many SUV and truck plants are running on overtime. The collapse in passenger-car demand is a challenge for nearly all automakers in the United States, including Japan's Toyota and Honda, which have the top-selling models in the compact and midsize car segments. Toyota executives said last month they are evaluating the company's U.S. model lineup. But Toyota also plans to build compact Corolla sedans at a new $1.6 billion factory it is building in Alabama with partner Mazda. The obstacles facing GM in its plans to close more auto factories became apparent on Tuesday as U.S. President Donald Trump threatened to block payment of government electric vehicle subsidies to GM. While it is not certain that Trump unilaterally has the power to do that, he made it clear he intends to use his office to pressure the company to keep open a small car plant in Ohio that GM says will stop building vehicles in March.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

MotorWeek Retro Review revisits 1984 Corvette

MotorWeek's Retro Reviews are always a great glimpse into the cars of yesteryear. However, the newly uploaded look back at the 1984 Chevrolet Corvette is an absolute treasure trove for any auto history buff. This is a full episode of the show from the '80s, and it's dedicated to all of the details about the newest 'Vette to hit the market at the time. Beyond just the usual drive and an in-depth walk around, one of the major highlights here is a brief look at some on the concepts that eventually resulted in the fourth-generation Corvette of 1984. The C4's shape harkens back to sketches from 1978, and there even shots of early clay models that led the way for the design. MotorWeek also takes a tour through the Bowling Green, KY, factory for a detailed inspection of the entire production process. John Davis repeatedly calls the Corvette "the plastic fantastic" during the episode, and he can't find too much negative to say about being behind the wheel of the then-new coupe. See how it stands up to your own memories in the clip above.