1970 Pro Street Nova (rolling) No Reserve!!! on 2040-cars

Auto blog

The real costs of keeping a Chevy Volt on the road

The release of the new, 2016 Chevy Volt is sure to bring a surge of used electric vehicles to the market as early adopters trade their older models in. Many of these cars are selling for a fraction of their original price, thanks in part to federal and state incentives that lowered the initial cost to the first owner, which opens these cars up to a whole new class of consumers. While the prices are getting attractive, potential buyers are still hesitant to buy a used EV due to uncertainty about service and repair costs, but there may be some good news on the horizon. The Chevy Volt comes with a battery warranty that is good for at least 8 years and 100,000 miles, but many of the Volts popping up on the market have passed that 100,000-mile mark. The threat of needing a new battery can be a deterrent, especially with some dealers quoting prices as high as $34,000 for a full "drive motor battery replacement." That sum is more than the MSRP of a 2016 model. Some of the fear of EV maintenance and repair comes from the mystery of the individual pieces that make up the drivetrain and charging system. If we take a look at the Volt in terms of analogs to a traditional internal-combustion vehicle, the outlook becomes a little more friendly. The Volt battery pack consists of three lithium-ion modules in a T-shaped arrangement, each of which can be serviced individually. Module 1 is made up of 90 cells and corresponds to GM part number 22954462, which retails for $3,258.33; module 2 is made up of 72 cells and corresponds to GM part number 22954463, which retails for $2,930.00; lastly, module 3 is made up of 125 cells and corresponds to GM part number 22954464, and retails for $4,933.33. These part numbers have been added to the dealer order systems but have not shown up in the distribution centers at this time. Although all three of the modules add up to a fairly large $11,121.66 total and are still on hold for dealer ordering, the good news is that in most cases these battery cell modules do not need to be replaced. There are many other individual pieces mounted on the battery pack that are serviceable, such as the Battery Energy Control Modules (BECM) and the Battery Interface Control Modules (BICM). These modules control and monitor the battery packs and charging system and have been known to fail while the lithium-ion battery cells are not at fault. Some have been replaced under warranty, but if you are stuck buying one they run about $255 a piece for the part.

GM plans to restart production in Mexico on May 20

MEXICO CITY — General Motors is tentatively planning to restart operations at its auto assembly plant in the Mexican city of Silao on May 20, according to a message to workers seen by Reuters on Sunday, as the car industry prepares to exit the coronavirus lockdown. Separately, the president of GM's Mexican unit advised suppliers to prepare to resume operations. “We are now beginning a new phase given the Mexican governmentÂ’s official announcement earlier this week to consider the transportation manufacturing industry as essential for the countryÂ’s economy,” Francisco Garza, president ofGeneral Motors de Mexico, wrote in an email to suppliers dated on Friday that was viewed by Reuters. The reopening of the plant  in Silao would be a positive signal for the auto sector in North America, whose supply lines are highly interconnected between the United States, Mexico and Canada. The plant in the central state of Guanajuato has been idled for weeks due to the coronavirus outbreak. Workers had previously been told to plan to return to their jobs on May 18. A GM spokeswoman said the company could not confirm when it would restart operations at any of its facilities in Mexico because it is awaiting more guidance from the government. The message to the plant's workers came after the government on Friday clarified when the industry could begin easing restrictions imposed because of the health emergency. On Wednesday, the government said automakers could start going back into production from May 18. It then withdrew that advice and suggested the new start date would be June 1. Finally it indicated the sector, which forms the backbone of Mexican manufacturing, could begin operating as soon as next week if companies had the required safety measures in place. U.S. officials and its auto industry have pressed Mexico's government to get its factories open again because American operations depend heavily on parts from south of the border. However, some politicians are wary of opening too fast. Mexico registered its first case of coronavirus weeks after the United States and Canada and the toll of daily infections and deaths in the country reached new peaks over the past few days. The Silao production facility, which makes highly profitable pickup trucks for GM, is one of the biggest automotive plants in Guanajuato, a major Mexican carmaking state. Related Video:

Callaway rolls out radical Corvette C7 GT3-R at Hockenheim

Leave it to Callaway to take a badass Corvette and make it even more so. Case in point: the new Callaway Corvette C7 GT3-R you see here. It made its big debut this past weekend during the season finale for the ADAC GT Masters series at the legendary Hockenheimring – the on-again, off-again home of the German Grand Prix. Why in Germany, you ask? Because that's where Callaway Competition is based. The racing division got its start in Heilbronn as Woeher & Ciccone back in 1985. It joined with US-based Callaway Cars in 1988 to distribute its modified Corvettes in Europe, and branched out into constructing racing cars in 1994. And this is its latest project. Designed in partnership between Callaway Competition in Germany and Canadian designer Paul Deutschman, the new GT3-R replaces the previous C6-based Z06.R GT3. It packs a 6.2-liter V8 pumping 600 horsepower through an X-Trac six-speed sequential gearbox. And as you can see, it sure looks the part. Callaway will be offering the new GT3-R to privateer teams for entry in a variety of racing series around the world. But it'll also be fielding the example you see here, sponsored by Whelen Engineering that – like Callaway Cars – is based in Connecticut. Callaway Corvette C7 GT3-R World Debut at Hockenheim October 3, 2015 Hockenheim, Germany – October 3, 2015 – This weekend's ADAC GT Masters Season Finale was the backdrop for the unveiling of Callaway Competition's new Callaway Corvette C7 GT3-R. Following a brief presentation to media and invited guests, the successor of the C6-based Callaway Z06.R GT3 was displayed to the public for the first time on October 3, 2015 at the Hockenheimring in Germany. Constructors of GT race cars since 1990 and based in Leingarten Germany, Callaway Competition possesses a wealth of experience, technical know-how and a broad network of specialized professional partners. These elements were crucial to conduct such a large undertaking. After nearly two years of comprehensive planning, intensive development and expert fabrication of vehicle components, Callaway Competition completed the first C7 GT3-R just a few weeks ago. Its striking design comes as a result of the collaboration between Canadian designer Paul Deutschman and team owners Giovanni Ciccone and Ernst Wohr. Mike Gramke, Uwe Hoffmann, Florian Mohring and Andre Zanke were also heavily involved in the vehicle's development.