1969 Chevy Nova Project Car Or Use For Parts on 2040-cars

Auto blog

2016 Chevrolet Camaro powers up, slims down

Don't be fooled by its familiar appearance, the 2016 Chevrolet Camaro is vastly different than its iconic predecessors. It has a new chassis, a fresh engine lineup, and is loaded with clever technologies that promise to invigorate and improve the sixth generation of Chevy's legendary sports car. It was revealed Saturday before a crowd of enthusiastic Camaro revelers on Belle Isle in Detroit. Redesigning the sports coupe was a heady task, especially as its archrivals, the Ford Mustang and Dodge Challenger, drive better and are more powerful than ever. But the new Camaro is aiming to be the best combination of handling and raw performance, with quick acceleration and competitive fuel economy. "Redesigning the Camaro is thrilling and challenging all at once, but the secret is to offer something more," Mark Reuss, General Motors executive vice president of product development, said in a statement. It all began with a weight-loss plan. The new Camaro shed more than 200 pounds compared with the outgoing car, with 133 pounds coming from a lighter body-in-white. Then engineers culled weight nearly everywhere, using aluminum for the instrumental panel frame and some suspension components to trim as much fat as possible. The slimmer body rests on new bones. The Camaro's rear-wheel-drive platform is lighter and stiffer in a bid to improve handling. It's a modified version of the underpinnings used by the Cadillac ATS, though about 70 percent of the architecture is unique to the Camaro. Chevy said structural rigidity is improved by 28 percent. As you'll see, healthy doses of Cadillac and Corvette technologies have been used to bolster the Camaro's drive character and performance. The new car is also expected to handle better thanks to a slightly smaller footprint. It is about two inches shorter in length, with most of that due to the more compact wheelbase. It's also an inch shorter in height and an inch slimmer in width. So yes, the Camaro will be leaner, but it will still be plenty mean. The Camaro SS tops the range (for now) with the Corvette's 6.2-liter V8 pushing put 455 horsepower and 455 pound-feet of torque. Known as the LT1, is has a cast aluminum block and cast aluminum cylinder heads, and it's fortified with direct injection, variable valve timing, and cylinder deactivation. About 20 percent of the engine's parts are said to be unique to the Camaro, including the exhaust manifolds.

GM recalls 83,572 SUVs for ignition switch issue

General Motors is recalling 83,572 SUVs from the 2011 and 2012 model years over a potential ignition lock actuator issue. In affected vehicles, the actuator isn't the right size, which could cause the ignition to get stuck in the "Start" position, and then either due to a jarring event or a "cool interior temperature" the ignition could switch back to the "Accessory" position. Doing so would cause a loss of power assistance and the airbags might not deploy. This is a different ignition issue than the one that's been ongoing for the past year. GM said it expects that less than 500 vehicles suffer from the problem, but that the pool could include vehicles from 2007 through to 2014 that have already been fixed, but with defective parts. The 2011-2012 SUVs included in the National Highway Traffic Safety Administration notice: Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado HD, Silverado LD, Suburban, Tahoe, GMC Sierra LD, Sierra HD, Yukon, and Yukon XL vehicles. GM will notify owners and dealers will inspect the ignition lock housing to see if it needs a free replacement. RECALL Subject : Ignition Lock Actuator may Bind Report Receipt Date: DEC 30, 2014 NHTSA Campaign Number: 14V827000 Component(s): ELECTRICAL SYSTEM Manufacturer: General Motors LLC SUMMARY: General Motors LLC (GM) is recalling certain model year 2011-2012 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado HD, Silverado LD, Suburban, Tahoe, GMC Sierra LD, Sierra HD, Yukon, and Yukon XL vehicles. In the affected vehicles, the ignition lock actuator may bind, making turning the key difficult or causing the ignition to get stuck in the "Start" position. CONSEQUENCE: If stuck in the "Start" position, the ignition may suddenly snap back into the "Accessory" position, causing a loss of engine, steering, and braking power, increasing the risk of a vehicle crash. If the vehicle is in a crash, the air bags may not deploy, increasing the risk of occupant injury. REMEDY: GM will notify owners, and dealers will inspect and replace the ignition lock housing, as necessary, free of charge. The manufacturer has not yet provided a notification schedule. Owners may contact GM customer service at 1-800-458-8006 (Cadillac), 1-800-222-1020 (Chevrolet), or 1-800-462-8782 (GMC). GM's number for this recall is 14696 for the original equipment, and 14912 for the service replacement parts.

GM plans to restart production in Mexico on May 20

MEXICO CITY — General Motors is tentatively planning to restart operations at its auto assembly plant in the Mexican city of Silao on May 20, according to a message to workers seen by Reuters on Sunday, as the car industry prepares to exit the coronavirus lockdown. Separately, the president of GM's Mexican unit advised suppliers to prepare to resume operations. “We are now beginning a new phase given the Mexican governmentÂ’s official announcement earlier this week to consider the transportation manufacturing industry as essential for the countryÂ’s economy,” Francisco Garza, president ofGeneral Motors de Mexico, wrote in an email to suppliers dated on Friday that was viewed by Reuters. The reopening of the plant  in Silao would be a positive signal for the auto sector in North America, whose supply lines are highly interconnected between the United States, Mexico and Canada. The plant in the central state of Guanajuato has been idled for weeks due to the coronavirus outbreak. Workers had previously been told to plan to return to their jobs on May 18. A GM spokeswoman said the company could not confirm when it would restart operations at any of its facilities in Mexico because it is awaiting more guidance from the government. The message to the plant's workers came after the government on Friday clarified when the industry could begin easing restrictions imposed because of the health emergency. On Wednesday, the government said automakers could start going back into production from May 18. It then withdrew that advice and suggested the new start date would be June 1. Finally it indicated the sector, which forms the backbone of Mexican manufacturing, could begin operating as soon as next week if companies had the required safety measures in place. U.S. officials and its auto industry have pressed Mexico's government to get its factories open again because American operations depend heavily on parts from south of the border. However, some politicians are wary of opening too fast. Mexico registered its first case of coronavirus weeks after the United States and Canada and the toll of daily infections and deaths in the country reached new peaks over the past few days. The Silao production facility, which makes highly profitable pickup trucks for GM, is one of the biggest automotive plants in Guanajuato, a major Mexican carmaking state. Related Video: