2005 Chevy Impala Ls ~ 4 Door Sedan ~3.8l V6 ~ Only 82,000 Miles! on 2040-cars

Auto blog

GM recalls select Tahoes, Yukons, Escalades for rear driveshaft issue

GM is recalling a number of its full-size SUVs due to an issue with the rear driveshaft assembly that could ultimately result in driveshaft failure. The actual number of total vehicles involved in the recall is small at just 1,789, but it’s spread out across the entire 2021 model year full-size GM vehicle lineup. That means a small number of every model is being recalled, including the Chevrolet Tahoe, Suburban, GMC Yukon, Yukon XL and the Cadillac Escalade and Escalade ESV. GM traced the issue back to certain driveshaft assemblies with ball bearings that were not properly heat treated. If theyÂ’re not properly heat treated, GM says that the balls may deform over time, causing noise and vibration. Continue to drive in this condition, and GM says the affected joint in the driveshaft assembly could seize, causing loss of drive power. However, the problem wonÂ’t present itself all at once, as GM says there will be a gradual increase of noises and vibrations before total failure. For those few owners with affected vehicles, GM says that it will replace the left and right rear driveshaft assemblies with properly-built units. Per usual with recalls, this will be done at your local dealership at no cost to the owner. If you have one of the recalled SUVs, expect to be notified mid-March. Related video:

Chevy admits there's confusion over Bolt and Volt names

Offering the possibility of 200 miles of driving range and the potential for a price of about $30,000, the Chevrolet Bolt is an incredibly enticing vehicle, and it has an opportunity to be a big player in the EV world. However, the hatchback has been plagued by one problem since the moment it debuted – the name. Bolt sounds very similar to Volt, Chevy's extended-range plug-in, and they can be easy to confuse in a conversation. That's not the best quality to have when trying to get a new vehicle's name out there among customers, and General Motors North America president Alan Batey told the Detroit Free Press that the company is aware of the problem. While the EV is definitely going into production, the model might be wearing a different moniker when it hits showrooms. "We're still in the decision phase. It could go either way," Batey said to the Free Press. He indicated the automaker still has about a year before a final decision is necessary. The Bolt will be built at GM's Orion Assembly plant in Michigan and will likely go on sale around 2017. That will put the Chevy on the market at roughly the same time as the 200-mile Tesla Model 3. Batey didn't seem too concerned, though. "Unlike Tesla, we can spread the cost over a whole lineup," he said to the Free Press. The future doesn't look quite so bright for the Spark EV, though. Batey suggested that it might not last once the longer-range Bolt fills that niche in the lineup. Related Video:

Experimental mid-engine XP-819 Corvette going up for auction

It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.