1999 Chevrolet Express 1500 Passenger Van on 2040-cars
Ramey, Pennsylvania, United States
|
176,000 mile
Inspection good until June 2014 Needs some work . . . It has been running rough for the past year. The mechanic told me the parts are cheap but the labor expensive, so we did not repair. (valve I think) Heat & Air conditioner does not work. Brake lights do not work. I did not realize until I got a notification from eBay that this vehicle was listed as a Salvage vehicle on 4-29-1999 in Glens Falls, NY. According to my title it was first titled in Pennsylvania in 12-5-2003. I do have a clear title. If you have any questions, please ask. If you would like to see and drive the vehicle before bidding, let me know. |
Chevrolet Express for Sale
Knapheide utility body 3500 drw truck
2003 chevrolet express 2500 not salvage damaged work van project car(US $5,500.00)
2008 chevy express 2500 cargo van v8 automatic trans one owner fleet maintained
2005 chevy express 2500 cargo 6.0l short wheelbase(US $6,500.00)
Conversion van.runs great.this van is ready to travel anywhere in no.america.
12 passenger, rear air/heat, 6.0l gas v8, abs, rubber floor mats, trades?(US $9,995.00)
Auto Services in Pennsylvania
Wright`s Garage ★★★★★
Williams, Roy ★★★★★
West Tenth Auto ★★★★★
West Industrial Tire ★★★★★
United Imports Inc ★★★★★
Toms Auto Works ★★★★★
Auto blog
Cadillac XT4 crossover to be built in Kansas City
Mon, Jan 8 2018Cadillac's upcoming XT4, a crossover we've previously known as the XT3 in a long series of spy shots of heavily camouflaged mules, will be built at General Motors' assembly plant in Kansas City on the same platform as the Chevrolet Malibu, Bloomberg reports, citing people familiar with the plan. That will give Cadillac another entry in the red-hot luxury crossover segment and, GM hopes, help to reverse a sales slump in the U.S. It'll also breath life into the Kansas City plant that makes the slow-selling Malibu, where GM cut a third shift last year, by sharing the assembly line between the crossover and sedan and defraying costs for each vehicle. The XT4 was known most recently as the XT3, with styling cues based on the Escala concept sedan from 2016. It's slightly smaller than the XT5, Cadillac's top-selling vehicle, and will also augment the full-size Escalade in Cadillac's stable of SUVs when it makes its expected debut later this year. Cadillac last week reported its second-highest-ever sales mark with 356,467 vehicles, an increase of 15.5 percent over 2016. But that mark papers over an 8 percent sales decline in the U.S. to 156,440 vehicles. The luxury brand is on a hot streak in China, where sales jumped 50.8 percent last year to 175,489 units.Related Video: Image Credit: Brian Williams Plants/Manufacturing Cadillac Chevrolet GM Crossover sales cadillac xt5 cadillac xt4 cadillac xt3
Next-gen Chevy Silverado and GMC Sierra may use carbon fiber
Thu, Dec 7 2017It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck
Race Recap: 2013 Indianapolis 500 better than Bollywood; all the emotion, none of the music [spoilers]
Mon, 27 May 2013If the 2013 Indy 500 were a movie it would be the one expected to win all the little statues come awards season, and if it were an athlete it would have made spectators watch in awe as it broke record after record. And this kind of talk comes after last year's race was considered one of the best ever - the last lap hijinks in 2012 and Takuma Sato's crash leading to a podium ceremony straight out of a Golden Globes tearjerker.
But this year's race delivered more than anyone expected, from the 250,000 fans to the commentators to the IndyCar series itself and, finally, to the guy who hopped through a two-mile window on Lap 197 to take the lead and keep it until the end.




