Original California Car, Excellent Condition, 5 Speed Manual on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

GM seatbelt recall affects over 1m Silverados and Sierras

The Basics: General Motors will recall 895,232 examples of the 2014-2015 Chevrolet Silverado and GMC Sierra 1500 pickups in the US. The campaign will also affect the trucks in markets worldwide, and the total number the company will recall is 1,037,982. The Problem: A steel cable connects the seatbelt to the vehicle, but over time repeated bending can cause the part to fatigue and separate. Injuries/Deaths: None reported. The Fix: Dealers will enlarge the side shield opening and install a pusher bracket on the tensioner. Technicians will also replace the entire tensioner assembly if necessary. If You Own One: GM will contact owners about the recall. The company hasn't said when those notifications would begin. More Information: There are still about 3,000 new examples of these older pickups at dealerships. Until mechanics fix the problem, these vehicles are subject to a stop-sale. Similar problems have affected the General's vehicles in the past. In 2015, the company recalled over 400,000 units of the 2011-2012 Chevrolet Malibu for fatiguing cables. It also hit over a million Lambda platform crossovers in 2014. GM Recalling Certain 2014-15 Pickups to Repair Seat Belts DETROIT – GM is voluntarily recalling 895,232 model year 2014-15 Chevrolet Silverado and GMC Sierra 1500 pickups in the United States because the flexible steel cable that connects the seat belt to the vehicle can fatigue and separate over time as a result of the driver repeatedly bending the cable when entering the seat. This issue was discovered through warranty data, and there have been no reports of crashes, injuries or fatalities related to this issue. For trucks in the field, dealers will enlarge the side shield opening, install a pusher bracket on the tensioner, and if necessary, replace the tensioner assembly. The recall in the United States includes a stop-sale of approximately 3,000 new 2014 and 2015 model year pickups still on dealer lots. Dealers will repair the vehicles prior to delivering them to customers. Customers will be notified by General Motors. They also can look up their vehicle identification number (VIN) at either https://vinrcl.safercar.gov/vin/ website or at https://my.gm.com/web/portal/ownercenter to see if their vehicle is part of the recall. GM also will voluntarily recall and repair these models in other countries where they are sold, including Canada, Mexico, and several countries in Latin America and the Middle East.

NHTSA upgrades probe into 1.7 million GM vehicles over wiper failures

WASHINGTON — The U.S. National Highway Traffic Safety Administration (NHTSA) said Tuesday it is upgrading an investigation into 1.7 million General Motors vehicles for windshield wiper failures. The auto safety agency opened the probe in November 2018 to see if GM needed to expand a 2016 recall of 2013 model year Chevrolet Equinox and GMC Terrain SUVs to cover additional vehicles. The engineering analysis probe covers 2010-2012 and 2014-2016 Equinox and Terrain vehicles. NHTSA could demand a recall after it completes the probe. NHTSA said it has reviewed 1,900 complaints and reports related to the issue in the 1.7 million vehicles. NHTSA said it has seen elevated failure rates in the 1.7 million vehicles, even though GM said the recalled vehicles have "double the warranty rate and five times the complaint rate." GM said it will "fully cooperate to support their investigation. We do not believe these windshield washer systems are defective." The wiper failures that prompted the 2016 recall were attributed to water and debris intrusion into the windshield wiper assembly ball joints, leading to excessive wear and eventual detachment of the ball joint. GM said it was installing an improved windshield wiper motor and transmission assembly and relocating a drain hole at the base of the windshield. Related Video: