2014 Chevrolet Captiva Sport Ltz on 2040-cars

Auto blog

Camaro-based Trans Am SE Bandit Edition borrows Burt Reynolds

For some reason, modifying modern Chevrolet Camaros into the lurching, reincarnated shells of the Pontiac brand is still a thing. If you're the perverse sort that likes this kind of thing, you should check out the latest product from the Trans Am Depot, which comes complete with an endorsement from the star of Smokey and the Bandit, Burt Reynolds. Yes, the new Trans Am SE Bandit Edition has been signed and endorsed by the man himself, but what's important here is not the signature on the dash, it's the bits of Camaro that have been modified. Aesthetically, that means a Bandit-and-Frog-approved set of T-tops, a front-opening hood with a very large, prominent shaker scoop, an equally large and prominent screaming chicken, and Trans Am-inspired front and rear fascias. And naturally, Burt Reynolds' signature adorns the dash. There are plenty of reminders in the cabin about this car's Hollywood inspiration, too. Bandit decals can be found on the front headrests and center console lid, there are chicken wings on the Camaro-spec plastic door inserts, and the black-and-tan color scheme matches nicely with the exterior look. And power? Well, Sheriff Buford T. Justice would have a lot more trouble keeping up with this Trans Am than he did with the original. The 7.4-liter LSX V8 has been paired with a 2.9-liter supercharger which is good for 840 horsepower. It's fast and loud, and even if you can't get behind the look (we can't), at least this Camaro-in-Trans Am's clothing can impress with its performance. The Bandit Edition is limited to just 77 units with prices starting around $115,000. You can check out the official video from Trans Am Depot, which comes with a decent helping of Burt Reynolds, up top. Related Video:

Chevy to offer new Cruze as a hatchback in the US

Chevrolet plans to offer a five-door hatchback version of the new Cruze in the United States, according to the latest intel from Automotive News. In addition to the sedan form we're familiar with, the outgoing Cruze was offered as a hatchback in some markets overseas, but not in America – a decision which Mark Reuss, GM's EVP in charge of product development, characterized as "a pre-bankruptcy planning mistake." The new Chevy Cruze is set to debut later this week. Although the American automaker has yet to confirm which bodystyles will be offered where, AN reports that a five-door model was already shown to dealers at their national meeting in Las Vegas last week. AN points out that the Ford Focus with which the new Cruze will be contending is offered as both a sedan and hatchback in America, with the latter accounting for some 40 percent of sales.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck