1994 Chevrolet Caprice Classic Wagon With Factory Lt-1 Motor - Hot Rod Wagon on 2040-cars

Auto blog

GM profit dips on truck changeover, but beats estimates

DETROIT — General Motors on Thursday reported a higher-than-expected quarterly profit despite a drop in production of high-margin pickup trucks, as it gears up for new models that are expected to boost profits next year. Like rivals Ford and Fiat Chrysler Automobiles, GM is banking on highly-profitable Chevy Silverado and GMC Sierra pickup trucks to lift profits, as consumers shift away from traditional passenger cars in favor of these larger, more comfortable trucks, SUVs and crossovers. During the first quarter, the process of changing over to GM's new pickups resulted in a drop in production of 47,000 units. GM Chief Financial Officer Chuck Stevens said the production drop had resulted in a drop in pre-tax profit of up to $800 million. Earlier this year, GM said its 2018 profits would be flat compared with 2017, but expected its all-new pickup trucks would boost margins starting in 2019. On Thursday, GM reiterated its full-year 2018 forecast for adjusted earnings in a range from $6.30 to $6.60 per share. The automaker said capital expenditures were more than $500 million higher in the quarter because of investments its new pickup trucks and a family of low-cost vehicles under development with Chinese partner SAIC Motor Corp. On Wednesday, rival Ford said it would stop investing in most traditional passenger sedans in North America. CFO Stevens told reporters on Thursday that GM has "already indicated that we will make significantly lower investments on a go-forward basis" in sedans. 2019 GMC Sierra View 21 Photos GM benefited from a lower effective tax rate in the quarter, but adjusted pre-tax margin fell to 7.2 percent from 9.5 percent a year earlier. Stevens said the company's profit margin should hit 10 percent or higher in the second quarter and for the full year. GM said material costs were $700 million higher in the first quarter, and it expects those costs to continue rising. The automaker said it would counter those increases with cost cutting measures. "It is a more difficult environment than it was three or four months ago," Stevens said when asked about rising commodity prices from potential steel and aluminum tariffs announced by the Trump administration. "But we are confident we can continue to offset that." The company reported quarterly net income of $1.05 billion or $1.43 per share, a drop of nearly 60 percent from $2.61 billion or $1.75 per share a year earlier. Analysts had on average expected earnings per share of $1.24.

Is the skill of rev matching being lost to computers?

If the ability to drive a vehicle equipped with a manual gearbox is becoming a lost art, then the skill of being able to match revs on downshifts is the stuff they would teach at the automotive equivalent of the Shaolin Temple. The usefulness of rev matching in street driving is limited most of the time – aside from sounding cool and impressing your friends. But out on a race track or the occasional fast, windy road, its benefits are abundantly clear. While in motion, the engine speed and wheel speed of a vehicle with a manual transmission are kept in sync when the clutch is engaged (i.e. when the clutch pedal is not being pressed down). However, when changing gear, that mechanical link is severed briefly, and the synchronization between the motor and wheels is broken. When upshifting during acceleration, this isn't much of an issue, as there's typically not a huge disparity between engine speed and wheel speed as a car accelerates. Rev-matching downshifts is the stuff they would teach at the automotive equivalent of the Shaolin Temple. But when slowing down and downshifting – as you might do when approaching a corner at a high rate of speed – that gap of time caused by the disengagement of the clutch from the engine causes the revs to drop. Without bringing up the revs somehow to help the engine speed match the wheel speed in the gear you're about to use, you'll typically get a sudden jolt when re-engaging the clutch as physics brings everything back into sync. That jolt can be a big problem when you're moving along swiftly, causing instability or even a loss of traction, particularly in rear-wheel-drive cars. So the point of rev matching is to blip the throttle simultaneously as you downshift gears in order to bring the engine speed to a closer match with the wheel speed before you re-engage the clutch in that lower gear, in turn providing a much smoother downshift. When braking is thrown in, you get heel-toe downshifting, which involves some dexterity to use all three pedals at the same time with just two feet – clutch in, slow the car while revving, clutch out. However, even if you're aware of heel-toe technique and the basic elements of how to perform a rev match, perfecting it to the point of making it useful can be difficult.

Why 2015 is going to be a huge year for trucks

Nissan chief executive Carlos Ghosn took center stage to introduce the 2016 Titan last week at the Detroit Auto Show. He spoke of the truck's new features, impressive Cummins V8 diesel engine and the extensive amount of time and money required to build a modern, competitive pickup truck. "We have done all of this because we see opportunity – an opportunity in the unmet needs of today's American truck customers," Ghosn said. He was speaking about the Titan, but his thoughts echo the industry's mindset: When it comes to trucks, find an opportunity and attack. Even with CAFE regulations looming and fickle consumer preferences, investing in trucks is a no-brainer for automakers. Some consumers will always need a truck for their job or lifestyle. And some people will always want one, whether they need it or not. With that in mind, here are four reasons why the pickup-truck sector is more important than ever and poised for growth in 2015. View 24 Photos The Nissan Titan Is Back Okay, it never left, but the Titan hadn't been redesigned since its launch in 2003, and Nissan sold more NV200s than Titans in 2014. It's an understatement to say the truck was languishing. That all changes with the 2016 model. The Titan will come in two variants, a traditional fullsize competitor and the Titan XD. The XD will lead the market launch, and it arrives late this year. It's pitched as a "whitespace" offering, Nissan sales and marketing vice president Fred Diaz said. The idea is to offer something in the general size and price range of a fullsize truck, but also have some of the capability of a heavy-duty truck. The XD uses a fully boxed ladder frame, the chassis design from Nissan's commercial division, and the wheelbase is about 20 inches longer than other Titan models. The XD, which Nissan is calling the flagship of the line, will be the only model with the 5.0-liter Cummins turbodiesel V8. It produces 310 horsepower and 555 pound-feet of torque, while being able to tow 12,000 pounds. V6 and V8 gasoline models will also be offered on the Titan XD and the standard, non-XD model. When production ramps up, the Titan will be sold with several cabs, beds and trims. New features include trailer sway control, an integrated trailer brake controller, more storage options in the cabin and even laminated front and rear side glass to reduce outside noise. All of this has given Nissan fresh confidence in an area where it admittedly has been lacking. "We can compete," Diaz told Autoblog.