2013 Chevy Camaro Ss Coupe....must See!!!! Spotless!!! on 2040-cars

Auto blog

GM patent reveals new two-stage turbocharger

Modern turbochargers may be some of the best ever made, but performance is something that engineers are always trying to improve. According to GM Inside News, General Motors (GM) is hoping to alleviate some of the negative aspects of a two-stage turbocharger setup with a newly-patented design. The patent, that was filed on May 19, 2016, reveals a clever bypass system that allows the engine, a four-cylinder unit, to optimize both the low-pressure and high-pressure inlets for its respective functions. According to the filing, a conventional two-stage turbocharger setup is engineered to allow both turbines to operate simultaneously at low and mid engine speeds. At high engine speeds, only the low-pressure turbine works. The setup can't isolate either the low or high pressure side, which can impair low-end performance. GM's new two-stage turbocharger setup looks to eliminate this by linking the high-pressure turbo to the exhaust manifold through the high-pressure inlet duct. The low-pressure turbo is attached to the high-pressure turbo by a low-pressure inlet duct, which is linked to a connecting channel. A single actuator that is housed in the exhaust manifold creates a bypass that can opens the high-pressure inlet or close the connecting channel. Depending on what the engine load and speed is, the ECU guides the actuator—a single rotating spindle with discs corresponding to flanges on the high and low pressure sides—to isolate one of the two turbos. Isolating the turbos allow the respective inlets to be engineered for the best possible fluid dynamic performance. The setup should increase performance and decrease lag. There's no word on what car this setup will make an appearance on, but it will most likely be used in premium vehicles before trickling down to the rest of GM's vehicles. Related Video: News Source: GM Inside News, AutoGuide via GM Authority Cadillac Chevrolet GM Technology Sedan turbo patent engine turbocharging

Camo'd Chevy Camaro ZL1 is one bad boy

Thanks to a fresh gallery of spy shots, we're getting a much better look at the next Chevrolet Camaro ZL1 during its development, and this machine is looking seriously mean. Unlike the last photos, the heavy cladding is gone from the body this time and is replaced by a camouflage wrap. That switch makes checking out the details a whole lot easier. The first thing you'll notice at the front is the massive grille that looks ready to devour anything that gets in the way. To add a little more menace, the lower air dam appears to jut out a bit more, as well. While harder to see in these latest shots, our spies say the hood still boasts an extractor similar to what's found on the Cadillac CTS-V. The big, double spoke wheels look great in black and really dominate the styling in profile. Look past them, and you notice some tweaked side sills, as well. At the very back, you can also spot some styling adjustments to the rear bumper. There's an unmissable wing back there, too. The powerplant for the ZL1 is still a mystery, but it's rumored to use the LT4 6.2-liter supercharged V8. The similar hood design as the CTS-V is one piece of evidence to support that. Even with the same engine, Chevy's engineers could tweak the output higher or lower than the Caddy. The wait to find out isn't too long because the ZL1 is anticipated to launch for the 2017 model year. Related Video:

GM's labor deal with UAW union on verge of ratification

Nov 15 (Reuters) - General Motors' tentative labor deal with the United Auto Workers (UAW) union closed in on ratification as the votes were counted on Wednesday. Following the approval earlier in the day by more than 60% of union members at the Detroit automaker's large Arlington, Texas, assembly plant, additional votes in favor have the deal close to clinching majority approval. The number of union locals, most of which are smaller, still to report vote totals is not large. After several large assembly plants voted against the deal earlier on Wednesday, some media had reported the deal was heading toward failure. But Arlington's support, followed by strong voting in favor by smaller warehouse and parts facilities, has put the deal on the brink of approval. This would mark the first ratification of a deal, which runs through April 2028, with one of the Detroit Three automakers. Ford and Stellantis voting is still under way, and workers at both companies were favoring ratification by comfortable margins. The UAW's GM vote tracking site currently shows approval of the contract leading by a 54% to 46% margin with almost 32,000 workers having cast votes out of about 46,000 UAW-represented GM workers. The Arlington plant, with about 5,000 UAW members, has the most of any GM plant. Voting officially ends on Thursday at 4 p.m. EST, although most votes will be cast on Wednesday. The UAW went on strike for more than six weeks against the Detroit Three, seeking better wages, working conditions and cost-of-living adjustments. All three companies agreed to tentative agreements about two weeks ago. Workers at other GM assembly plants voted against the deal, including 60% of workers at its Fort Wayne, Indiana, truck plant, 53% at its Wentzville, Missouri, plant, 58% of workers at GM's Lansing Grand River plant and 61% of workers at the Lansing Delta Township plant. Seven of GM's 11 assembly plants rejected the deal. In addition to Arlington, workers at plants in Detroit, Fairfax, Kansas; and Lake Orion, Michigan; approved the agreement. Only nine facilities are still listed without vote totals on the UAW vote tracker, including GM's Lockport, New York, components plant with about 1,200 members. Those voting in favor of the agreement have a lead of almost 2,500 and many of the facilities still to come include workers who stand to receive large pay increases upon ratification.