2010 Chevy Camaro Lt Rs 6spd Sunroof Htd Leather 47k Mi Texas Direct Auto on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Leveling kit now available for Chevy Colorado, but not yet for GMC Canyon

In various bits of news this year concerning the Chevrolet Colorado and GMC Canyon pickups, we kept hearing about a front leveling kit. GM Authority found a few details in early order guides in January. In February, the kit came up in relation to the Canyon's AT4 Off-Road Performance Package, and again with AEV's upgraded Colorado Bison. After three months of waiting, GMA has more info. The kit eliminates the trucks' raked stance by raising the front by one inch, using an electro-coated upper spacer and a polyurethane lower spacer in order to maintain the proper suspension geometry. Installation is a bolt-on job with low-profile nuts, but the task will require a spring compressor. Fitted properly, the kit doesn't void GM's new vehicle warranty on the Colorado. Why do we only mention the Colorado? Because for some reason, the kit isn't available for the Canyon yet as a standalone component; the GMC stays raked without one of the aforementioned option packages. For Chevy, the leveling kit is compatible with any trim in four-wheel drive except the ZR2. It cannot be installed on two-wheel-drive trucks, nor any truck wearing wheels that are 20 inches or above. The kit is available now, ordered through any Chevy dealer for $150. There is a treat in store for GMC buyers, though, but it requires spending a lot more money. GM Authority discovered that the 2021 Yukon will offer the brand's first illuminated emblem. Priced at $475 as a dealer-installed option, a backlit glow will show off the GMC logo in the grille. The brand makes the logo in red and black, it's thought the red logo will get the nod, at least at first. Only the front logo earns the spotlight, not the one on the tailgate. GMA says the tchotchke will be available on all four trims when the new full-size crossover goes on sale in a few months.

A car writer's year in new vehicles [w/video]

Christmas is only a week away. The New Year is just around the corner. As 2014 draws to a close, I'm not the only one taking stock of the year that's we're almost shut of. Depending on who you are or what you do, the end of the year can bring to mind tax bills, school semesters or scheduling dental appointments. For me, for the last eight or nine years, at least a small part of this transitory time is occupied with recalling the cars I've driven over the preceding 12 months. Since I started writing about and reviewing cars in 2006, I've done an uneven job of tracking every vehicle I've been in, each year. Last year I made a resolution to be better about it, and the result is a spreadsheet with model names, dates, notes and some basic facts and figures. Armed with this basic data and a yen for year-end stories, I figured it would be interesting to parse the figures and quantify my year in cars in a way I'd never done before. The results are, well, they're a little bizarre, honestly. And I think they'll affect how I approach this gig in 2015. {C} My tally for the year is 68 cars, as of this writing. Before the calendar flips to 2015 it'll be as high as 73. Let me give you a tiny bit of background about how automotive journalists typically get cars to test. There are basically two pools of vehicles I drive on a regular basis: media fleet vehicles and those available on "first drive" programs. The latter group is pretty self-explanatory. Journalists are gathered in one location (sometimes local, sometimes far-flung) with a new model(s), there's usually a day of driving, then we report back to you with our impressions. Media fleet vehicles are different. These are distributed to publications and individual journalists far and wide, and the test period goes from a few days to a week or more. Whereas first drives almost always result in a piece of review content, fleet loans only sometimes do. Other times they serve to give context about brands, segments, technology and the like, to editors and writers. So, adding up the loans I've had out of the press fleet and things I've driven at events, my tally for the year is 68 cars, as of this writing. Before the calendar flips to 2015, it'll be as high as 73. At one of the buff books like Car and Driver or Motor Trend, reviewers might rotate through five cars a week, or more. I know that number sounds high, but as best I can tell, it's pretty average for the full-time professionals in this business.