2006 Chevy 2500hd *crew Cab 4x4*6.5 Ft Bed*super Clean*4dr*warranty $14495/offer on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Leveling kit now available for Chevy Colorado, but not yet for GMC Canyon

In various bits of news this year concerning the Chevrolet Colorado and GMC Canyon pickups, we kept hearing about a front leveling kit. GM Authority found a few details in early order guides in January. In February, the kit came up in relation to the Canyon's AT4 Off-Road Performance Package, and again with AEV's upgraded Colorado Bison. After three months of waiting, GMA has more info. The kit eliminates the trucks' raked stance by raising the front by one inch, using an electro-coated upper spacer and a polyurethane lower spacer in order to maintain the proper suspension geometry. Installation is a bolt-on job with low-profile nuts, but the task will require a spring compressor. Fitted properly, the kit doesn't void GM's new vehicle warranty on the Colorado. Why do we only mention the Colorado? Because for some reason, the kit isn't available for the Canyon yet as a standalone component; the GMC stays raked without one of the aforementioned option packages. For Chevy, the leveling kit is compatible with any trim in four-wheel drive except the ZR2. It cannot be installed on two-wheel-drive trucks, nor any truck wearing wheels that are 20 inches or above. The kit is available now, ordered through any Chevy dealer for $150. There is a treat in store for GMC buyers, though, but it requires spending a lot more money. GM Authority discovered that the 2021 Yukon will offer the brand's first illuminated emblem. Priced at $475 as a dealer-installed option, a backlit glow will show off the GMC logo in the grille. The brand makes the logo in red and black, it's thought the red logo will get the nod, at least at first. Only the front logo earns the spotlight, not the one on the tailgate. GMA says the tchotchke will be available on all four trims when the new full-size crossover goes on sale in a few months.

Most of the US won't get 2016 Chevy Volt

Every major plug-in vehicle launch in the US has been a patchwork operation, with automakers focusing their initial efforts on targeted locations like California where they expect to sell the most units. Today, we learned that even five years into the plug-in car project, the game remains the same. According to GM, the second-gen Chevy Volt is going to be rolled out in the same manner. In fact, GM is limiting availability of the 2016 model year Volt so much that most of the US will not have access to the car at all. For 39 states, the second-gen Volt will first be available as a 2017 model year vehicle at some point in the spring of 2016. When GM announced the buying process for the new Volt, it made it clear that dealers in California would be the first to place their orders. Hybrid Cars now reports that the first deliveries will be also limited to California and 10 other states that follow the California Air Resourced Board (CARB) rules: Connecticut, Massachusetts, Maryland , Maine, New Hampshire, New Jersey, New York, Oregon, Rhode Island, and Vermont. GM spokesman Kevin Kelly told AutoblogGreen that this is all according to plan. "Chevrolet has a shortened model year for the 2016 Chevy Volt that will have a limited distribution network," he said. "The 2016 Volt will be sold in our strongest EREV markets. The 2017 Chevrolet Volt will begin production early this spring and will be available throughout the country." It appears that non-CARB state Volt customers will be able to order their Volts starting October 1, according to documents posted on Hybrid Cars, where we also learn that 2016 Volt production for California started in August, will begin in late October for the other 10 CARB states, and in early 2016 for the rest of the US. Unsurprisingly, dealers outside of the 11 CARB states have been complaining that they can't order the much-anticipated new Volt for their customers just yet. Related Video: