Excellent Condition, All Recent Work, Truck Stripped, Taken Down To Bare Metal!! on 2040-cars

Auto blog

GM recalls 55,000 trucks, SUVs for separating axles, fuel pump failures

General Motors issued four separate recalls covering eight of its truck and SUV models for issues related to fuel pump and half-shaft failure. In total, the four campaigns include more than 55,000 vehicles spread out over three brands and six model years, but they've sorted themselves neatly into two categories. Let's dive in.  Axle separation Four models are being recalled for potential axle separation: The 2023 Cadillac XT5, 2023 GMC Acadia, 2023 Chevy Blazer and 2023 Chevy Traverse. The number of units affected is incredibly small (10 units each times two recalls, for a total potential population of just 20 cars). In each case, a small number left the factory with half-shaft assemblies that may have been missing the retention rings that keep them in place, possibly allowing the axles to separate or eject from the transmission. In the case of the XT5 and Acadia, it's the right-side axle assembly; Chevy dealers, however, will have to check the left side.  Fuel pump failure Again, we have multiple vehicles being recalled for similar issues, but in this case they're a bit more distinct. The first of these recalls covers the 2021-2022 Chevy Equinox and 2022 GMC Terrain. GM says a supplier-initiated change may have led to fuel pumps shipping with inadequate clearances to allow for the prescribed flow of fuel, meaning the pump could starve the engine. Customers experiencing the issue may see a check engine light and experience engine hesitation. In some cases, the cars may not start at all. Chevy and GMC will replace the units in question with correctly specified pumps.  The second recall covers a fairly specific cross-section of GM's HD truck lines. 2017-2019 Silverado and Sierra HD trucks sold with the diesel engine and a dual-tank configuration may have shipped with a rear fuel pump that is susceptible to fouling by debris, preventing fuel from properly transferring to the front tank, or, in extreme cases, resulting in a collapse of the rear tank. This issue can lead to inaccurate/erratic fuel tank readings, engine hesitation, a check-engine light or failure to start.  In both cases, GM will inspect and replace faulty units free of charge for customers. Expect notifications to be delivered by March.  Related video: Recalls Cadillac Chevrolet GMC Ownership Safety Truck SUV

Callaway debuts its new C7 Stingray at National Corvette Museum

Callaway showed off its first tuned version of the 2014 Corvette Stingray at the National Corvette Museum last week, giving the rampant enthusiasts of America's sports car a look at the roughly 620-horsepower, supercharged rocket.
Unlike the Corvette SC610 we showed you back in January, this Stingray packs a fair bit more oomph. Horsepower is only up ten ponies, but torque has jumped from 556 pound-feet to "at least" 600 pound-feet. Neither horsepower nor torque is official quite yet, although Callaway is expecting to know just what its creation can do once testing and validation is completed later this month.
The 6.2-liter, supercharged V8 now boasts a new, three-element intercooler, which Callaway claims only allowed the inlet air temperature to increase by ten degrees Fahrenheit during dyno runs. Previous designs saw a 35-degree-Fahrenheit jump. The exhaust system has also been fettled with, and now is even less restrictive.

Experimental mid-engine XP-819 Corvette going up for auction

It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.