1957 Chevrolet Bel Air Two Door Hardtop Retro Hot Rod V8/muncie Drive 2day Video on 2040-cars

Auto blog

Race Recap: Rolex 24 at Daytona was fast and feisty

Let the record show that victory at the 2015 Rolex 24 at Daytona went to the No. 02 Chip Ganassi Racing with Felix Sabates Target/Ford EcoBoost Riley DP driven by Verizon IndyCar drivers Scott Dixon and Tony Kanaan and NASCAR drivers Jamie McMurray and Kyle Larson. The winner did 740 laps to cover 2,634.3 miles in 24 hours and 57.667 seconds. That's a statement to this year's pace in spite of 18 cautions, two more than last year: the Michael Shank Racing Ligier got pole with a time of 1:39.194, slower than last year's pole time of 1:38.270; however, the winning car last year only did 695 laps. The fight for top honors was shaved to a four-car battle over the first third of the event. The No. 02 Ganassi car took the lead on the first lap, swapping it well into the night with the No. 01 Ganassi car, the No. 10 Wayne Taylor Racing Corvette DP, and the defending champion No. 5 Action Express Corvette DP, all of them staying within about 20 seconds of one another. The Action Express car had a fuel connector come loose and lost three laps getting towed back to the pits to have it reattached, but was back in the lead 18 hours in. The No. 01 Ganassi car dropped out with recurring clutch problems 22 hours in, retiring not long after. A race-within-the-race is where the concluding action happened, a seven minute, 30-second dash from the end of the last caution to the checkered flag. During the penultimate pit stops with an hour to go, Dixon was in second place followed Jordan Taylor in the Wayne Taylor Racing DP into the pits but beat him out, taking the lead. The Action Express car was in third. In the last pit stops of the race, Dixon gained even more time, getting a four-second advantage over Taylor. Then a full-course caution came out twenty minutes before the finish when a Prototype Challenge car hit the wall and caught fire, bunching up the field. That closed the pits, but the Wayne Taylor Racing car had to pit during that yellow because of a miscalculation of driver time. No driver can be behind the wheel for more than four hours in a six-hour period but Jordan Taylor was going to go over, so he came in to swap out for brother Ricky. That cost the team any chance of second place, since they took an additional drive-through penalty for entering closed pits. When the track went green again, Sebastien Bourdais in the Action Express car stayed all over Dixon for the final five laps but couldn't get around him.

Why an independent rear suspension for GM's new, full-sized SUVs wasn't easy

A Motor Trend report last month laid out how Cadillac's 4.2-lier twin-turbo Blackwing V8 could be an orphan due to cost concerns in the GM empire. Last-minute chassis changes to Cadillac's new sedans and XT6 crossover led to engine bays that couldn't fit the Blackwing. On the SUV side, according to the report, the new independent rear suspension for big people haulers cost so much to implement that GM ruled out reworking the Escalade to accept the Blackwing. At least one commenter rightly asked how could a suspension swallow that much money. A new piece in Motor Trend has the answer. The excellent Alissa Priddle spoke to Tim Herrick, GM's executive chief engineer for full-size trucks, about why the clean-sheet IRS cost "multimillions of dollars."  First, GM would need to build a new body shop at the Arlington, Texas plant that assembles the automaker's big SUVs to stamp the numerous wholly new parts and panels accommodating an IRS. Then GM would need to design and pay for a new assembly process. On top of those up-front costs, there was the incremental cost of the four-link IRS components being more expensive than those in the trucks' former leaf-sprung solid axles. Herrick endured so many rejections for so long that he remembers the date and time when he got approval for the new unit. He said it came down to a meeting where he told a higher-up, "I'll make you a deal: If we get to the reveal, or if we launch this and you think this was a dumb idea, I'll hand you my badge and let you walk me out." Head to Motor Trend to read the full story. Based on Herrick being on stage to help present the new SUVs to the press, and on our First Ride in the new Chevrolet Tahoe and Suburban at GM's Milford Proving Grounds, it appears this will have a happy ending for all involved. Furthermore, since Herrick worked on the T1 platform that supports the big SUVs as well as the light- and heavy-duty pickups, he understood the demands on the commercial side, too. That could be why when Roadshow asked Tim Asoklis, chief engineer of the Tahoe and Suburban, if the new IRS could endure life in the Chevrolet Silverado and GMC Sierra, Asoklis answered, "Oh, absolutely." Related Video:    

2020 Chevy Silverado, GMC Sierra recalled due to faulty brake component

General Motors is recalling 2020 Chevrolet Silverado 1500 and GMC Sierra 1500 pickups to fix a defect in the trucks' brake system. Certain Silverado and Sierra pickups were produced with brake-caliper bolts that were not heat-treated. Without heat-treating, the bolts are weaker than they should be, and there is a risk that they could fail, which would affect the trucks' braking performance, possibly leading to a crash. In total, 20,352 vehicles are affected. Owners of affected trucks will be contacted by GM. Dealers will inspect the bolts and replace those that are defective. Related Video: