1998 Cadillac Eldorado 2dr Cpe Leather Low Miles on 2040-cars

Auto blog

First Cadillac ELR rolls off the line

Gearing up for the Belle Isle Grand Prix this weekend, General Motors invited some of the Chevrolet and Cadillac racecar drivers out to its Detroit-Hamtramck assembly plant. While there, the racers - including IndyCar Driver and Chevrolet Volt owner, Simona De Silvestro - witnessed the very first 2014 Cadillac ELR to roll off the assembly line.
These vehicles are not destined for customers, however, but instead pre-production units will be used by engineers for testing purposes. Actual production of ELR consumer models is expected to commence closer to the end of this year. As a refresher, this range-extended electric Cadillac shares much of its powertrain with the Volt but will have a sportier coupe design inspired by the Converj Concept. De Silvestro manged to snap a few images of here own, which you can see in the gallery below.

GM investing $2 billion in Tennessee plant to build Cadillac Lyriq, other EVs

DETROIT — General Motors said on Tuesday it will invest $2 billion to convert its Spring Hill, Tennessee, factory to produce electric vehicles, starting with the new Cadillac Lyriq, alongside existing combustion-engine Cadillacs. Spring Hill will be GM's third U.S. electric vehicle factory, along with existing plants in Detroit and Orion Township, Michigan. The Tennessee plant was built in 1990 as the exclusive source for GM's now-defunct Saturn brand. The Cadillac Lyriq crossover is slated to go into production in Spring Hill in late 2022, according to AutoForecast Solutions (AFS), which tracks industry production plans. AFS said it expects some electric vehicle production will be announced at a later date for a factory in Mexico. Among additional investments, GM on Tuesday said it will spend $32 million at its truck plant in Flint, Michigan, to increase production of the Chevrolet Silverado and GMC Sierra heavy-duty pickups. GM will spend $100 million to shift production of the redesigned GMC Acadia crossover from Spring Hill to a plant near Lansing, Michigan. Spring Hill will continue to build the gas-engine Cadillac XT5 and XT6 crossovers. The plant also will build other future electric vehicles in addition to the Lyriq. The automaker's plans for investing in U.S. factories comes with two weeks left in the U.S. presidential election campaign. President Donald Trump and Democratic rival Joe Biden are competing for support from auto workers in Midwestern swing states. GM Chief Executive Mary Barra has outlined plans to invest $20 billion by 2025 in new electric vehicles and battery technology. The automaker is spending $2.2 billion to overhaul and retool its Detroit-Hamtramck factory to build a GMC Hummer EV electric pickup truck in late 2021, followed by an automated robotaxi and other electric vehicles. GM builds its electric Chevrolet Bolt at a large assembly plant north of Detroit.

Super Cruise’s failsafes

Even though Super Cruise is not a fully autonomous system, it incorporates redundancies like those used in aircraft to ensure failsafe operation. Before taking off on a 700-mile, 11-hour test drive of the system — and putting my life in its hands without my hands on the wheel — I sat down with Daryl Wilson, lead development engineer for Super Cruise, to get a deep dive into the system and its critical safety backups. Autoblog: First, what makes Super Cruise different from similar systems? Wilson: The key differentiator for Super Cruise is hand-free driving. It's an industry first in that respect. Our competitors require the driver at minimum to place their hands on the wheel with some frequency to ensure that the car knows that the driver is there. We don't. Two key technologies allow us to do this. One is our Driver Attention System, which is our methodology for making sure the driver is engaged with the vehicle and engaged with the road. This is a driver assist system, not a fully autonomous system. So it requires driver engagement. We use an infrared camera that constantly monitors the driver's face to determine the direction they're looking. We're looking for the driver to be what we call on-road — not on the center stack, not to left or right or down. That's all done by the tracking of the face. We also track that the eyes are open. It's infrared because at night you need to illuminate the face and you can't be shining a light into the driver's face. Then we have our lidar mapping that provides a foundation for control and redundancy to ensure safe performance. Autoblog: How does the mapping act as a redundant feature? Wilson: This system is only for use on divided, controlled access highways. What I mean by a divided highway is something more than a painted line between you and oncoming traffic. Whether that's a grassy area in between the lanes or a concrete barrier, anything that separates you from oncoming traffic. That's the divided highway part. The controlled access part is entrance ramps and exit ramps. Not with roads that cross at grade, with traffic crossing at the same level. To do that we geofenced these roads to ensure that operation is only allowed in these conditions. We don't just recommend you use it there; we ensure that you only use it there.