1967 Cadillac Fleetwood Eldorado Coupe,first Yr Prod, Low Vin#, Marina Blue on 2040-cars

Auto blog

GM Ultium tech can scavenge heat from everywhere, even you

GM likes to give us tidbits about its Ultium platform from time to time, and today it’s telling us about the platformÂ’s ability to capture waste heat from the propulsion system. In addition to capturing from the propulsion system, it can also capture humidity from both inside and outside the vehicle and even from passengersÂ’ body heat. Yes, you, your family and/or your friends are a usable heat source as far as GM EVs are concerned. It then deploys the heat in an advantageous way. If at this point, youÂ’re screaming, "Heat pump!" youÂ’d be right. WeÂ’re talking about an elaborate heat pump system that GM is using for its Ultium-based vehicles. Every Ultium-based GM vehicle gets this system that is covered by 11 patents and four publications. The waste heat it collects is used in a number of ways, but its primary use is to heat the cabin quickly and efficiently. GM claims it can heat the cabin of its Ultium-based vehicles quicker than vehicles with traditional internal combustion engines. Plus, when put to use, GM claims that using the heat pump provides its EVs with up to 10% more range than theyÂ’d have without. Beyond heating the cabin, the heat pump is capable of putting waste heat to use by preheating the battery prior to charging so that you can charge quicker. The system can even cool the propulsion system in preparation for Watts to Freedom (WTF) launch control starts. GM says this was vital in helping the Hummer EV achieve its bonkers 0-60 mph time of about 3 seconds. “Having a ground-up EV architecture gives us the freedom to build in standard features like UltiumÂ’s energy recovery capabilities,” said Doug Parks, GM executive VP of global product development, purchasing and supply chain. “This helps us squeeze more efficiency, performance and overall customer benefit out of our EVs.” GM says itÂ’s been developing heat pump technology since the EV1 and its heat pump. This is the modern evolution of that technology, and GM says itÂ’s going to be implemented in every Ultium-based vehicle as a standard feature. Related video: Green Cadillac Chevrolet GM GMC Technology Electric Future Vehicles

Ringbrothers drops more hints about its wild SEMA creations

Ringbrothers isn't finished teasing its SEMA creations. First we got a sliver of rear quarter on a 1969 Chevrolet Camaro that revealed a bundle of carbon fiber and SEMA-obligatory deep-dish wheels. The Wisconsin tuner's now announced its litter of cars headed to the show and a few specs, along with two shadowy drawings. The Camaro, christened with the name Valkyrja and a two-tone paint job, gets stretched in two directions with severe fender flares to widen the body and an extended wheelbase. We're not sure what's happening with the Camaro's snout in the drawing, but under that bulging hood we'll find a 416-cubic-inch LS V8 from Wegner Motorsports. Wegner built the 416-cu-in supercharged LS3 V8 that powered Ringbrothers' 1,000-hp G-Code Camaro in 2016.  The second member of the gang is a 1969 Ford Mustang Mach 1 dubbed Unkl. The exterior begs for attention with a deep blue sea paint job, deep front chin spoiler, bulging hood, yellow brake calipers, and what looks like a racing number inside a roundel on the doors. Unkl gets its motivation from a 520-cu-in Boss V8 built by Kaase Racing Engines, rumored to throw about 800 hp.    Finally, Ringbrothers is bringing its Cadillac Madam V for another Las Vegas go-round after giving the custom coupe some updates. The Madam V is a 1948 Cadillac Series 62 fastback coupe body placed atop an ATS-V chassis, first shown in 2016. The firm didn't elaborate on the changes, so all we can expect for now are the coupe's postwar good looks mixed with new-millennium engineering, and a 3.6-liter twin-turbo V6 with 464 hp under that exceptionally long hood.    For any in attendance at the show, the Valkyrja Camaro debuts at the BASF booth on Tuesday, Nov. 5, 2019 at 9:30 a.m., the Unkl Mustang gets revealed a couple hours later at the Flowmaster/Holley booth, and the Madam V Cadillac will be on display throughout the show at the Ringbrothers booth.

Cadillac moving back to Detroit after four years in New York City

After four years in New York City, The Wall Street Journal reports that Cadillac is moving its headquarters back to Detroit. This comes about four months after former head Johan de Nysschen was ousted from the automaker for a variety of reasons, including slumping sales and a product line not in concert with consumer tastes. It's also months after a Cadillac spokesperson told The Detroit Free Press that "It's 100 percent that we're staying [in New York City], that was never a question." Let's be clear about this, the move to New York was not Cadillac's biggest issue. As contributing editor James Riswick reminded us this morning, "the decision to sell three similarly sized large sedans, a variety of obsessive BMW-fighting cars, and only one crossover was not done while they were in New York." That was all planned years ago, before de Nysschen ever joined the company. He may not have righted the ship, but he didn't set it on its course. Note that the XT4, Caddy's second crossover after the SRX-replacing XT5, is just now hitting the market. The move to Manhattan was meant to give Cadillac more autonomy and put its leadership in a place where they could get a sense of what a luxury car buyer wants and needs. Detroit is great, but it can be an echo chamber, especially in a company as large and storied as General Motors. The problem is that Cadillac still relies heavily on Detroit and that poor communication was slowing development, according to the report. Steve Carlisle, a long-time GM employee, took over the brand after de Nysschen was let go. He and more than 100 others work in New York. Related Video: