2001 Cadillac Sedan Deville-sharp-nice-clean-beautiful Luxury on 2040-cars

Auto blog

Cadillac's Super Cruise — look, Elon, no hands!

Cadillac is about to start selling vehicles with an autonomous driving mode and TechCrunch got an early look at the technology in a production car. "Wait for the green light and let go," the Cadillac engineer instructed. That's it. The car was driving itself. I, the person behind the steering wheel, was no longer the driver. Cadillac's Super Cruise system was driving. The 2018 Cadillac CT6 sped along U.S. 23 under the direction of Super Cruise. Traffic was light and the weather was perfect. The system held the Cadillac sedan in lane and responded appropriately to traffic. I spent an hour on the expressway and touched the steering wheel and pedals only a few times. Super Cruise made the drive boring. I think that's the point. Here's how it works Super Cruise is available once the driver navigates the vehicle onto an expressway. When ready, a little icon is displayed by the speedometer and the driver hits a button on the steering wheel to switch it on. Once the light bar on top of the steering wheel turns green, the driver can let go. Super Cruise is driving.This steering wheel light bar is key to the operation. When green, the driver knows Super Cruise is in control. Blue means the driver interrupted the system to change lanes and red means Super Cruise needs the driver to confirm they're paying attention and not checking Twitter. When active, Super Cruise controls the steering and speed, but again, only on an expressway. This is done through onboard sensors and using GPS and mapping data. GM employed GeoDigital, a startup in GM Venture's portfolio, to map 160,000 miles of expressways in the U.S. and Canada. The car company then used Super Cruise-equipped vehicles to test each mile. This combination of onboard systems combined with map data makes the system feel polished and sophisticated. During my admittedly limited time in the vehicle, the CT6 precisely held its position in the lane and confidently handled sweeping curves at speed. There was no wiggling or squirming — from the Cadillac or myself. The car was in control, and I felt safe. Although the driving conditions were perfect for my test ride, during adverse weather, the system will work normally until one of the key systems is unable to operate.

Don Draper's 1965 Cadillac Coupe de Ville up for auction

Few have ever nor ever will embody the sheer confidence and style of Don Draper, the main character on the hit AMC drama Mad Men. But if you can't quite match his style, at least you can drive his car. Now that the series has now concluded its eight-year run, the studio behind it is selling off a whole mess of artifacts from the show through ScreenBid, a specialist Hollywood memorabilia auctioneer. There's a good 1,300 lots up for grabs, from props to costumes. But the lot that's caught our attention is this 1965 Cadillac Coupe de Ville. Don picked this car up in the fifth season and drove it until the penultimate episode. These are the wheels he (spoiler alert!) drove across the country, got repaired in Oklahoma, and ultimately gave to a kid working at the motel before making his way by bus to the Bonneville Salt Flats in the final episode. At the time of writing, bidding had reached $25,000 with four days still to go. Cadillac first used the de Ville as a trim level on the Series 62 before spinning it off into its own model line. 1965 was the first year of the third-generation de Ville, stretching a massive 224 inches (over 18 and a half feet!) long. Powering over 4,600 pounds of personal American luxury was an equally massive 7.0-liter V8 that drove 340 horsepower through a three-speed automatic transmission. The name wasn't retired until 2005 when the final DeVille (as it was styled by then) was replaced by the DTS, which itself was shorthand for DeVille Touring Sedan. Cadillac produced the last DTS in 2011, finally putting to rest a name that had, in one form or another, been used since 1949. Few cars had the kind of presence that the third-gen Coupe de Ville did, though, and Draper knew it. Or at least the show's producers did.

Our favorite mid-engine Corvette theories and rumors

The mid-engine Corvette! We just saw blurry photos through the foliage, and are hearts are all aflutter because it means that this car is real. And it's the most " never before" Corvette since 1984. Which leads us to all kinds of wacky theories and speculation. Everybody knows something or heard from a guy. None of those guys (or gals) from GM are talking to Autoblog, to be clear. But that won't stop us from stirring the pot. Let's go over a few point-by-point. The pushrod engine will be replaced by an overhead-cam V8 Car and Driver has repeatedly reported that an overhead-cam engine will come after the mid-engine Corvette's debut with an old-school pushrod. We've heard the same thing firsthand, albeit from a source with no connection to the development of the Corvette or powertrain. "At some point two valves can't pass future emissions regulations," said the guy we know. While the pushrod engine is compact, the design makes it difficult - if not impossible - for sophisticated variable valve timing (and lift) systems that control combustion with more precision. Hasty conclusion: The pushrod engine has a finite life in front of it. This one's a lock, it's a just a matter of when. Bowling Green's new paint shop is really the mid-engine assembly line Credit to Reddit for this one. Like we said, everybody knows a guy. But let's look deeper. The new paint facility costs $439 million dollars and adds 450,000 square feet, almost half the size of the existing plant. Plus GM announced another $290 million in upgrades at Bowling Green Assembly. That sure sounds like a lot of money, but you can actually spend that much on a paint booth. Porsche spent 500 million Euros (about $561 million dollars) to add the Macan assembly to its Leipzig, Germany plant in 2014. Chrysler shelled out $850 million for a paint shop in Sterling Heights, Michigan. GM spent $600 million for a new paint shop at the Fairfax (Kansas City) plant. Honda, on the other hand, is working on a thrifty $210 million project in Marysville, Ohio that includes a 300,000 square foot expansion, and the low-volume Acura NSX facility only cost $70 million. Hasty conclusion: The square footage and cost could easily mean a new assembly line instead of (or in addition to) a paint line. And if the NSX plant was really that cheap, GM could have hidden a similar sum in its existing announcements.