1967 Cadillac Deville Calais Hardtop 4-door 500ci on 2040-cars

Auto blog

Super Cruise’s failsafes

Even though Super Cruise is not a fully autonomous system, it incorporates redundancies like those used in aircraft to ensure failsafe operation. Before taking off on a 700-mile, 11-hour test drive of the system — and putting my life in its hands without my hands on the wheel — I sat down with Daryl Wilson, lead development engineer for Super Cruise, to get a deep dive into the system and its critical safety backups. Autoblog: First, what makes Super Cruise different from similar systems? Wilson: The key differentiator for Super Cruise is hand-free driving. It's an industry first in that respect. Our competitors require the driver at minimum to place their hands on the wheel with some frequency to ensure that the car knows that the driver is there. We don't. Two key technologies allow us to do this. One is our Driver Attention System, which is our methodology for making sure the driver is engaged with the vehicle and engaged with the road. This is a driver assist system, not a fully autonomous system. So it requires driver engagement. We use an infrared camera that constantly monitors the driver's face to determine the direction they're looking. We're looking for the driver to be what we call on-road — not on the center stack, not to left or right or down. That's all done by the tracking of the face. We also track that the eyes are open. It's infrared because at night you need to illuminate the face and you can't be shining a light into the driver's face. Then we have our lidar mapping that provides a foundation for control and redundancy to ensure safe performance. Autoblog: How does the mapping act as a redundant feature? Wilson: This system is only for use on divided, controlled access highways. What I mean by a divided highway is something more than a painted line between you and oncoming traffic. Whether that's a grassy area in between the lanes or a concrete barrier, anything that separates you from oncoming traffic. That's the divided highway part. The controlled access part is entrance ramps and exit ramps. Not with roads that cross at grade, with traffic crossing at the same level. To do that we geofenced these roads to ensure that operation is only allowed in these conditions. We don't just recommend you use it there; we ensure that you only use it there.

[UPDATE] Cadillac Blackwing gets ticket to Italy, to go to work in a supercar

UPDATE: It seems MAT's belief it had secured a supply of Cadillac's 4.2-liter Blackwing V8 was premature, and based on a handshake deal before GM sold its Turin engine center to Italy's Punch Group. Shortly after Hagerty ran the story, GM sent a statement to the outlet reading, in part, "We do not have an agreement in place with Manifattura Automobili Torino (MAT) to provide or sell the Blackwing engine. ... Our team is following up with MAT president Paolo Garella to discuss the misunderstanding." MAT also submitted a statement to Hagerty, saying, in part, "We thank GM for the clarification. Although a signed agreement was not finalized between the parties, we were under the impression that our counterpart was committing to making this engine available to MAT at conditions yet to be defined. ... We hope that this misunderstanding will not compromise our relations with GM and possible future collaborations." The original article follows: Some necessary cost-cutting at Cadillac led to switching the new CT4, CT5, and Escalade to older platforms. The revised architecture plan meant Cadillac's newest top-tier products couldn't fit Cadillac's newest top-tier engine, the 4.2-liter twin-turbo DOHC V8 known as Blackwing. That engine would serve limited duty at full power in the now-dead CT6-V, and at reduced output in the CT6 Platinum V8 trim before ending its bright, brief domestic life. But the story isn't over, the rebirth of Blackwing coming from a most surprising locale: Turin, Italy. Before the canceled Geneva Motor Show, Hagerty spoke to Paolo Garella, CEO of Manifattura Automobili Torino; that's the company better known as MAT, makers of the New Stratos and contract engineering house for boutique screamers like the Aspark Owl electric hypercar, Apollo Intensa Emozione, and SCG003C. Garella told the outlet, "We have an agreement with General Motors" for a supply of Blackwings, which would be developed and built at the General Motors Propulsion Engineering Center (PEC) in Turin. Since 2005, the PEC has been used to develop GM's global diesel engines and electronics. MAT's plan is to put the V8 into a new limited-run car MAT is creating from its own design. Then another surprising turn: Belgium-based global auto supplier Punch Group bought the PEC, with plans to work with GM on projects in progress until at least the end of 2021. Nothing changes as far as MAT is concerned, except perhaps a chance for an even closer collaboration with Punch Turin.

GM to build $1.3 billion Cadillac plant in China

General Motors has gotten approval to build a $1.3 billion manufacturing facility for its Cadillac brand in China. China's National Development and Reform Commission signed off on plans for GM to build the plant in the country's Shanghai's Jinqiao zone; construction is expected to begin in June of this year. According to a Bloomberg report, the plant will have an annual production capacity of 150,000 units.
No surprise here, but Cadillac would like to sell a lot more cars in the plush Chinese luxury market. The brand moved only 30,010 cars in China last year, compared with 400k for Audi, and about 330k for BMW. With Cadillac already telling us that it would be moving production of its XTS sedan to China - a production decision that saves having to pay 25-percent import tariffs - approval of the factory is a critical win for the company.
In fact, according to earlier comments by GM China president Bob Socia, it's at least conceivable that Chinese-built Cadillacs could be shipped back to the US for sale. The brave new world of globalization, getting stranger by the minute.