2012 Cadillac Cts Sedan on 2040-cars

Auto blog

Cadillac to recall 20,000 SRX models over wheels that could fall off

A potential issue with the lug nuts on 19,871 units of the 2013 Cadillac SRX in the US and Canada has lead to a recall of the luxury crossover. Those lug nuts that have a Teflon topcoat, identified by their bluish tint, could loosen and cause "creaking, rattling or grinding noises or steering vibrations." In the worst case scenario, a wheel could fall off, but there have been no reports of that happening, nor any reports of accidents or injuries due to the issue.
This is the second recall action on the SRX over the last few months. In March, Cadillac recalled 27,000 SRX models over a transmission programming issue. General Motors will begin notifying customers with the potentially faulty parts on June 3, at which time they can take their vehicles to dealers to have the tires rotated and new nuts installed. A further 7,397 SRXs exported from North America also face the recall action.

GM recalls full-size truck, SUVs and vans over faulty shifter mechanism

Twelve different General Motors vehicles from the 2013 model year, up to 54,686 units in total, are being recalled over two potential issues with their steering columns. The models in question, all full-size trucks, SUVs or vans, are the: Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Express, Silverado, Suburban, Tahoe, and GMC Savana, Sierra, Yukon and Yukon XL.
The affected vehicles were built with a fractured parking lock cable or "a malformed steering column lock actuator gear in the lock module assembly." As a consequence, they could shift out of park without the brake pedal being applied or with the key removed or in the off position.
A bulletin from the National Highway Traffic Safety Administration indicates that the recall should begin on January 17. GM will notify owners, at which time they can take their vehicles to their dealers for repair free of charge. Have a look at the bulletin below for more information.

[UPDATE] Cadillac Blackwing gets ticket to Italy, to go to work in a supercar

UPDATE: It seems MAT's belief it had secured a supply of Cadillac's 4.2-liter Blackwing V8 was premature, and based on a handshake deal before GM sold its Turin engine center to Italy's Punch Group. Shortly after Hagerty ran the story, GM sent a statement to the outlet reading, in part, "We do not have an agreement in place with Manifattura Automobili Torino (MAT) to provide or sell the Blackwing engine. ... Our team is following up with MAT president Paolo Garella to discuss the misunderstanding." MAT also submitted a statement to Hagerty, saying, in part, "We thank GM for the clarification. Although a signed agreement was not finalized between the parties, we were under the impression that our counterpart was committing to making this engine available to MAT at conditions yet to be defined. ... We hope that this misunderstanding will not compromise our relations with GM and possible future collaborations." The original article follows: Some necessary cost-cutting at Cadillac led to switching the new CT4, CT5, and Escalade to older platforms. The revised architecture plan meant Cadillac's newest top-tier products couldn't fit Cadillac's newest top-tier engine, the 4.2-liter twin-turbo DOHC V8 known as Blackwing. That engine would serve limited duty at full power in the now-dead CT6-V, and at reduced output in the CT6 Platinum V8 trim before ending its bright, brief domestic life. But the story isn't over, the rebirth of Blackwing coming from a most surprising locale: Turin, Italy. Before the canceled Geneva Motor Show, Hagerty spoke to Paolo Garella, CEO of Manifattura Automobili Torino; that's the company better known as MAT, makers of the New Stratos and contract engineering house for boutique screamers like the Aspark Owl electric hypercar, Apollo Intensa Emozione, and SCG003C. Garella told the outlet, "We have an agreement with General Motors" for a supply of Blackwings, which would be developed and built at the General Motors Propulsion Engineering Center (PEC) in Turin. Since 2005, the PEC has been used to develop GM's global diesel engines and electronics. MAT's plan is to put the V8 into a new limited-run car MAT is creating from its own design. Then another surprising turn: Belgium-based global auto supplier Punch Group bought the PEC, with plans to work with GM on projects in progress until at least the end of 2021. Nothing changes as far as MAT is concerned, except perhaps a chance for an even closer collaboration with Punch Turin.