2006 Cadillac Xlr Base Convertible 2-door 4.6l on 2040-cars

Auto blog

2016 Cadillac ATS-V blasts into LA

The first details about the 2016 Cadillac ATS-V recently hit the web ahead of the official debut at the 2014 Los Angeles Auto Show. Now, the latest model to wear Caddy's high-performance V moniker is officially official, and the specs are even better than initial rumors suggested.
The latest figures actually give the ATS-V a hair more power than first believed, with 455 horsepower and 445 pound-feet of torque pumping out of the twin-turbocharged 3.6-liter V6. With a standard electronic limited-slip differential keeping rear wheels in check, Cadillac claims that the model sprints to 60 miles per hour in 3.9 seconds and on to a top speed of 185 mph. Buyers have two transmission choices that both offer launch control: a six-speed manual featuring Active Rev Match and no-lift shifting, or an eight-speed automatic.
Thoroughly revised suspension and braking systems should also mean that the ATS-V excels at more than just going in a straight line. The chassis itself receives extra bracing to boost overall stiffness by 25 percent over lesser ATS models. On top of that, a host of suspension upgrades front and rear, including third-generation Magnetic Ride Control dampers, mean quicker steering response and a tighter ride. Plus, Brembo six-piston calipers up front and four-pistons in the rear should bring rapid deceleration. To tune it all to the driver's whim, the Performance Traction Management system gives five settings to choose from for stability and traction control.

[UPDATE] Cadillac Blackwing gets ticket to Italy, to go to work in a supercar

UPDATE: It seems MAT's belief it had secured a supply of Cadillac's 4.2-liter Blackwing V8 was premature, and based on a handshake deal before GM sold its Turin engine center to Italy's Punch Group. Shortly after Hagerty ran the story, GM sent a statement to the outlet reading, in part, "We do not have an agreement in place with Manifattura Automobili Torino (MAT) to provide or sell the Blackwing engine. ... Our team is following up with MAT president Paolo Garella to discuss the misunderstanding." MAT also submitted a statement to Hagerty, saying, in part, "We thank GM for the clarification. Although a signed agreement was not finalized between the parties, we were under the impression that our counterpart was committing to making this engine available to MAT at conditions yet to be defined. ... We hope that this misunderstanding will not compromise our relations with GM and possible future collaborations." The original article follows: Some necessary cost-cutting at Cadillac led to switching the new CT4, CT5, and Escalade to older platforms. The revised architecture plan meant Cadillac's newest top-tier products couldn't fit Cadillac's newest top-tier engine, the 4.2-liter twin-turbo DOHC V8 known as Blackwing. That engine would serve limited duty at full power in the now-dead CT6-V, and at reduced output in the CT6 Platinum V8 trim before ending its bright, brief domestic life. But the story isn't over, the rebirth of Blackwing coming from a most surprising locale: Turin, Italy. Before the canceled Geneva Motor Show, Hagerty spoke to Paolo Garella, CEO of Manifattura Automobili Torino; that's the company better known as MAT, makers of the New Stratos and contract engineering house for boutique screamers like the Aspark Owl electric hypercar, Apollo Intensa Emozione, and SCG003C. Garella told the outlet, "We have an agreement with General Motors" for a supply of Blackwings, which would be developed and built at the General Motors Propulsion Engineering Center (PEC) in Turin. Since 2005, the PEC has been used to develop GM's global diesel engines and electronics. MAT's plan is to put the V8 into a new limited-run car MAT is creating from its own design. Then another surprising turn: Belgium-based global auto supplier Punch Group bought the PEC, with plans to work with GM on projects in progress until at least the end of 2021. Nothing changes as far as MAT is concerned, except perhaps a chance for an even closer collaboration with Punch Turin.

Cadillac SRX production moving to TN, next-gen Equinox going to Mexico

It's a good week for the town of Spring Hill, TN, as General Motors has announced that its factory in the city of 31,000 will receive a $185 million contract to produce engines. On top of that, the next-generation Cadillac SRX crossover will be built at the factory (NA models are presently built in Ramos, Arizpe Mexico), which was once famous for being the home of GM's now-defunct Saturn brand.
The factory is one of GM's six facilities around the globe that will screw together the company's new line of three- and four-cylinder Ecotec engines. Spring Hill currently builds the 2.0-liter, turbocharged Ecotec, as well as the naturally aspirated 2.4 and 2.5-liter variants.
Spring Hill's vehicle assembly lines were idled in 2009, but were reactivated in 2011. The SRX is just one of the products meant to benefit from last year's $350-million investment, and should have a positive impact, creating or retaining around 1,800 positions at the factory.