2005 Cadillac Xlr Base Convertible 2-door 4.6l on 2040-cars

Auto blog

Cadillac XT3 caught covered in copious camouflage

While a bit difficult to tell thanks to the impressive camouflage used, what we're looking at here is likely the upcoming Cadillac XT3. There are a few details that stand out to lend credence to this prediction. There are a handful of sharp angles scattered throughout that are in line with Cadillac's modern design language. Specifically in the LED running lights and on the side mirrors. The rear profile also is reminiscent of the current, and slightly larger XT5. The rear lights extend into the D-pillars, which would match the current Escalade. We get a pretty clear picture of the rear suspension on this XT3. It's clearly an independent rear suspension using coil springs. While General Motors uses independent suspension on some of its crossovers, we can't quite match it to a particular model. We believe that if the XT3 is based on an existing model (which it almost certainly is), the platform and suspension have been substantially modified. The XT3 could use a version of the D2XX platform that underpins the Buick Envision. However, we know from a previous report that the XT3 will likely be built at the factory that produces the Buick LaCrosse and Chevy Malibu. The XT5 uses a modified version of the LaCrosse/Malibu platform, so it's possible the XT3 could use a shorter version of the XT5 chassis. Depending on how small the XT3 ends up being, it might even share a platform with the Chevy Trax and Buick Encore. However, considering their economy car roots and torsion-bar rear suspension, we think that's the least likely. Regardless of what chassis is underneath its crisp bodywork, we expect the XT3 to be released sometime next year. Related Video:

2015 Cadillac Escalade

I have never liked traveling to Monterey, CA. The picturesque coastal city is about 300 miles from my home in Los Angeles, which means cramped and uncomfortable regional aircraft are part of the equation when the turnaround is only one night. Over the years, I have cursed the LA Basin's bumper-to-bumper traffic en route to the airport, argued with TSA personnel over carry-on baggage and waited countless hours for the fog to lift just for the anguish of being packed into a small regional jet for the flight. Of course, the process repeats on the trip home with equal misery.
Yet this time I am not suffering.
Cadillac has dropped its all-new 2015 Escalade in my driveway. Instead of battling city congestion, attempting to reason with misinformed government agents, snacking on a too-small bag of pretzels and physically rubbing shoulders with a dubious stranger for 90-plus minutes within the confines of a bumpy aircraft, I have chosen to forgo air travel and drive myself door-to-door in a fullsize luxury sport utility vehicle.

Super Cruise’s failsafes

Even though Super Cruise is not a fully autonomous system, it incorporates redundancies like those used in aircraft to ensure failsafe operation. Before taking off on a 700-mile, 11-hour test drive of the system — and putting my life in its hands without my hands on the wheel — I sat down with Daryl Wilson, lead development engineer for Super Cruise, to get a deep dive into the system and its critical safety backups. Autoblog: First, what makes Super Cruise different from similar systems? Wilson: The key differentiator for Super Cruise is hand-free driving. It's an industry first in that respect. Our competitors require the driver at minimum to place their hands on the wheel with some frequency to ensure that the car knows that the driver is there. We don't. Two key technologies allow us to do this. One is our Driver Attention System, which is our methodology for making sure the driver is engaged with the vehicle and engaged with the road. This is a driver assist system, not a fully autonomous system. So it requires driver engagement. We use an infrared camera that constantly monitors the driver's face to determine the direction they're looking. We're looking for the driver to be what we call on-road — not on the center stack, not to left or right or down. That's all done by the tracking of the face. We also track that the eyes are open. It's infrared because at night you need to illuminate the face and you can't be shining a light into the driver's face. Then we have our lidar mapping that provides a foundation for control and redundancy to ensure safe performance. Autoblog: How does the mapping act as a redundant feature? Wilson: This system is only for use on divided, controlled access highways. What I mean by a divided highway is something more than a painted line between you and oncoming traffic. Whether that's a grassy area in between the lanes or a concrete barrier, anything that separates you from oncoming traffic. That's the divided highway part. The controlled access part is entrance ramps and exit ramps. Not with roads that cross at grade, with traffic crossing at the same level. To do that we geofenced these roads to ensure that operation is only allowed in these conditions. We don't just recommend you use it there; we ensure that you only use it there.