Florida,esv,stretch Conversion Limo, Celebrity Owned,black/black,loaded,l@@k on 2040-cars

Auto blog

[UPDATE] Cadillac Blackwing gets ticket to Italy, to go to work in a supercar

UPDATE: It seems MAT's belief it had secured a supply of Cadillac's 4.2-liter Blackwing V8 was premature, and based on a handshake deal before GM sold its Turin engine center to Italy's Punch Group. Shortly after Hagerty ran the story, GM sent a statement to the outlet reading, in part, "We do not have an agreement in place with Manifattura Automobili Torino (MAT) to provide or sell the Blackwing engine. ... Our team is following up with MAT president Paolo Garella to discuss the misunderstanding." MAT also submitted a statement to Hagerty, saying, in part, "We thank GM for the clarification. Although a signed agreement was not finalized between the parties, we were under the impression that our counterpart was committing to making this engine available to MAT at conditions yet to be defined. ... We hope that this misunderstanding will not compromise our relations with GM and possible future collaborations." The original article follows: Some necessary cost-cutting at Cadillac led to switching the new CT4, CT5, and Escalade to older platforms. The revised architecture plan meant Cadillac's newest top-tier products couldn't fit Cadillac's newest top-tier engine, the 4.2-liter twin-turbo DOHC V8 known as Blackwing. That engine would serve limited duty at full power in the now-dead CT6-V, and at reduced output in the CT6 Platinum V8 trim before ending its bright, brief domestic life. But the story isn't over, the rebirth of Blackwing coming from a most surprising locale: Turin, Italy. Before the canceled Geneva Motor Show, Hagerty spoke to Paolo Garella, CEO of Manifattura Automobili Torino; that's the company better known as MAT, makers of the New Stratos and contract engineering house for boutique screamers like the Aspark Owl electric hypercar, Apollo Intensa Emozione, and SCG003C. Garella told the outlet, "We have an agreement with General Motors" for a supply of Blackwings, which would be developed and built at the General Motors Propulsion Engineering Center (PEC) in Turin. Since 2005, the PEC has been used to develop GM's global diesel engines and electronics. MAT's plan is to put the V8 into a new limited-run car MAT is creating from its own design. Then another surprising turn: Belgium-based global auto supplier Punch Group bought the PEC, with plans to work with GM on projects in progress until at least the end of 2021. Nothing changes as far as MAT is concerned, except perhaps a chance for an even closer collaboration with Punch Turin.

Expect the Cadillac XT3 small crossover in late 2018

Cadillac's sedan-heavy lineup can't complete in this crossover-crazy market, it seems. The Detroit News spoke to Cadillac boss Johan de Nysschen and found out some more details about the brand's plan to alter its lineup to cater more to current consumer tastes. It's no surprise that these plans would include a small crossover, because de Nysschen has been talking about a vehicle smaller than the XT5 like this since at least 2015. The report also pins the Fairfax Assembly Plant, where GM builds the Buick LaCrosse and the Chevrolet Malibu, as the site for what could be called the XT3's production. That's not an immediately obvious choice, since the LaCrosse and Malibu are based on the latest evolution of the Epsilon platform, known as E2XX. And the XT5 is based on a crossover version of that same platform (known as C2XX), while XT3 is expected to be smaller than the XT5. So perhaps there's a different assembly line going into Fairfax, or the C2XX platform can be significantly shortened. We assume that the XT3 would be built on a smaller platform, perhaps the Gamma II that underpins the Chevrolet Trax and Buick Encore – which are built in either South Korea or Mexico, depending on which market they are to be exported to. The Encore is selling very well for Buick, with sales figures increasing through late last year. Another possibility is the D2XX platform that underpins the Chinese-built Buick Envision and the GMC Terrain and Chevrolet Equinox, perhaps with assembly happening at the CAMI plant in Ontario. At this early stage, without confirmation of GM as to what platform the XT3 will use or where it will really be built, it's too early to say what the Fairfax rumor means. This isn't the first time we've heard about a small Cadillac crossover. Back in 2015, de Nysschen told us to expect it sometime in 2018. But later that year, speaking to Reuters, he posited that it'd be closer to 2019. The Detroit News says de Nysschen told them it'll launch in the second half of 2018, splitting the difference between what we'd heard previously. Remember, Cadillac's only two vehicles in the segment are the XT5 and Escalade. We know that the brand is almost certainly scrambling to fill the holes in that side of the lineup. We think a three-row crossover will slot between the two, probably called the XT7.

New V6 engines are only the start at Cadillac

Cadillac debuted its new family of V6 engines Friday, but that's not all General Motors' luxury brand has in store for the coming years. The six-cylinder powerplants will certainly help Cadillac in the near term, but they're just two of the many parts of the company's future strategy. GM has invested $12 billion in Cadillac to help the brand grow over the next five years, and the company will launch eight new products between now and 2020. That all starts with the launch of the CT6 flagship later this year – a fullsize luxury sedan we'll see for the first time in New York on March 31. The CT6 will introduce several new features and technologies to the Cadillac range, and with its launch also begins the slow restructuring of Cadillac's model-naming system. The new nomenclature means CT and XT badges for cars and utilities, respectively. Cadillac says that of the eight new vehicles it plans to launch by 2020, five of them will be first-time offerings in market segments where the brand currently does not play. But it's not just about new products – new powertrains are an important part of the Cadillac story, too. After the new V6 engines – a naturally aspirated 3.6-liter and a twin-turbocharged 3.0-liter engine – launch later this year in the 2016 ATS, CTS and CT6, the company says it has a strategy for V8 power – possibly a twin-turbo application – as well as future electrification. Cadillac also says it's working on adding four- and six-cylinder diesel powertrains, though it's unclear which vehicles will make use of those engines. This new six-cylinder engine family is indeed important, with Cadillac's chief engineer, David Leone, calling it the "most advanced V6 in the industry." With 335 horsepower, the 3.6-liter engine is the highest output, naturally aspirated V6 powerplant Cadillac has done – and that's SAE-certified, and on regular fuel. Beyond that, the 3.0-liter mill (pictured at right) marks the first application of GM's active fuel management system on a twin-turbocharged engine. This means that when full power isn't necessary, the TTV6 can run as a 2.0-liter V4 in order to save fuel. New transmissions are also part of the V6 engine story. GM's all-new eight-speed Hydra-Matic 8L45 gearbox will be paired to the 3.6-liter V6, and the 3.0-liter TTV6 will use the company's existing 8L90 transmission that is already found in the Chevrolet Silverado and GMC Sierra pickups (with the 6.2-liter engine).