76k Orig Miles Az Car Red On Red New Top Rust Free Loaded Car 77 78 75 79 74 on 2040-cars

Auto blog

2015 Cadillac ATS, CTS recalled over brake issue

A problem with the brakes on the 2015 ATS and CTS has prompted Cadillac to issue a recall. According to the notice below from the National Highway Traffic Safety Administration, the issue revolves around the bracket that connects the brake pedal assembly and the rod that actuates the brakes. Even under normal operation, that bracket could fracture, impeding the ability to slow or stop the vehicle. That, as you're surely aware, could increase the risk of a crash. The issue affects a reported 2,163 vehicles in the United States. Owners will need to be bring their vehicles in to their local dealership to have those brackets replaced starting on August 1. See the complete recall notice below. RECALL Subject : Brake Pedal Bracket may Fracture Report Receipt Date: JUN 09, 2015 NHTSA Campaign Number: 15V358000 Component(s): SERVICE BRAKES, HYDRAULIC Potential Number of Units Affected: 2,163 Manufacturer: General Motors LLC SUMMARY: General Motors LLC (GM) is recalling certain model year 2015 Cadillac ATS and CTS vehicles. The affected vehicles have a bracket between the brake pedal assembly and the rod that actuates the brakes that may fracture during normal brake pedal operation. CONSEQUENCE: If the bracket fractures, the driver would not be able to apply the brakes, increasing the risk of a crash. REMEDY: GM will notify owners, and dealers will inspect the vehicle and replace any affected bracket, free of charge. The recall is expected to begin August 1, 2015. Owners may contact Cadillac customer service at 1-800-458-8006. GM's number for this recall is 15352. NOTES: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Cadillac considering more radical ATS-V

Cadillac is stepping up its performance game with the launch of the new ATS-V and CTS-V, but it's not about to rest on the laurels it removed from its own badge. While it's tipped to launch additional V models in the future, the latest word is Caddy could also come out with an even more extreme version of the ATS-V in the near future. According to Car and Driver, the prospect is on the table: "We might have something down the road that is a little bit more aggressive," chief engineer Dave Leone said, while another source pegged its potential arrival for 2017. It's too early to say what would constitute the more extreme model. The magazine points toward the Mercedes-AMG Black Series as an example. Jaguar took a similarly extreme approach with the XKR-S GT, as BMW has with the M3 GTS. As it is, the ATS-V is offered in both coupe and sedan variants with a 3.6-liter twin-turbo V6 producing 464 horsepower channeled to the rear wheels through a six-speed manual. Cadillac reportedly considered employing a dual-clutch transmission and all-wheel drive, but went the old-school route to avoid excess weight and (no doubt) cost.

Why an independent rear suspension for GM's new, full-sized SUVs wasn't easy

A Motor Trend report last month laid out how Cadillac's 4.2-lier twin-turbo Blackwing V8 could be an orphan due to cost concerns in the GM empire. Last-minute chassis changes to Cadillac's new sedans and XT6 crossover led to engine bays that couldn't fit the Blackwing. On the SUV side, according to the report, the new independent rear suspension for big people haulers cost so much to implement that GM ruled out reworking the Escalade to accept the Blackwing. At least one commenter rightly asked how could a suspension swallow that much money. A new piece in Motor Trend has the answer. The excellent Alissa Priddle spoke to Tim Herrick, GM's executive chief engineer for full-size trucks, about why the clean-sheet IRS cost "multimillions of dollars."  First, GM would need to build a new body shop at the Arlington, Texas plant that assembles the automaker's big SUVs to stamp the numerous wholly new parts and panels accommodating an IRS. Then GM would need to design and pay for a new assembly process. On top of those up-front costs, there was the incremental cost of the four-link IRS components being more expensive than those in the trucks' former leaf-sprung solid axles. Herrick endured so many rejections for so long that he remembers the date and time when he got approval for the new unit. He said it came down to a meeting where he told a higher-up, "I'll make you a deal: If we get to the reveal, or if we launch this and you think this was a dumb idea, I'll hand you my badge and let you walk me out." Head to Motor Trend to read the full story. Based on Herrick being on stage to help present the new SUVs to the press, and on our First Ride in the new Chevrolet Tahoe and Suburban at GM's Milford Proving Grounds, it appears this will have a happy ending for all involved. Furthermore, since Herrick worked on the T1 platform that supports the big SUVs as well as the light- and heavy-duty pickups, he understood the demands on the commercial side, too. That could be why when Roadshow asked Tim Asoklis, chief engineer of the Tahoe and Suburban, if the new IRS could endure life in the Chevrolet Silverado and GMC Sierra, Asoklis answered, "Oh, absolutely." Related Video: