1996 Cadillac Eldorado Coupe Low Miles Garage Kept Books Records Mint No Reserve on 2040-cars

Auto blog

Super Cruise’s failsafes

Even though Super Cruise is not a fully autonomous system, it incorporates redundancies like those used in aircraft to ensure failsafe operation. Before taking off on a 700-mile, 11-hour test drive of the system — and putting my life in its hands without my hands on the wheel — I sat down with Daryl Wilson, lead development engineer for Super Cruise, to get a deep dive into the system and its critical safety backups. Autoblog: First, what makes Super Cruise different from similar systems? Wilson: The key differentiator for Super Cruise is hand-free driving. It's an industry first in that respect. Our competitors require the driver at minimum to place their hands on the wheel with some frequency to ensure that the car knows that the driver is there. We don't. Two key technologies allow us to do this. One is our Driver Attention System, which is our methodology for making sure the driver is engaged with the vehicle and engaged with the road. This is a driver assist system, not a fully autonomous system. So it requires driver engagement. We use an infrared camera that constantly monitors the driver's face to determine the direction they're looking. We're looking for the driver to be what we call on-road — not on the center stack, not to left or right or down. That's all done by the tracking of the face. We also track that the eyes are open. It's infrared because at night you need to illuminate the face and you can't be shining a light into the driver's face. Then we have our lidar mapping that provides a foundation for control and redundancy to ensure safe performance. Autoblog: How does the mapping act as a redundant feature? Wilson: This system is only for use on divided, controlled access highways. What I mean by a divided highway is something more than a painted line between you and oncoming traffic. Whether that's a grassy area in between the lanes or a concrete barrier, anything that separates you from oncoming traffic. That's the divided highway part. The controlled access part is entrance ramps and exit ramps. Not with roads that cross at grade, with traffic crossing at the same level. To do that we geofenced these roads to ensure that operation is only allowed in these conditions. We don't just recommend you use it there; we ensure that you only use it there.

Cadillac XT3 caught covered in copious camouflage

While a bit difficult to tell thanks to the impressive camouflage used, what we're looking at here is likely the upcoming Cadillac XT3. There are a few details that stand out to lend credence to this prediction. There are a handful of sharp angles scattered throughout that are in line with Cadillac's modern design language. Specifically in the LED running lights and on the side mirrors. The rear profile also is reminiscent of the current, and slightly larger XT5. The rear lights extend into the D-pillars, which would match the current Escalade. We get a pretty clear picture of the rear suspension on this XT3. It's clearly an independent rear suspension using coil springs. While General Motors uses independent suspension on some of its crossovers, we can't quite match it to a particular model. We believe that if the XT3 is based on an existing model (which it almost certainly is), the platform and suspension have been substantially modified. The XT3 could use a version of the D2XX platform that underpins the Buick Envision. However, we know from a previous report that the XT3 will likely be built at the factory that produces the Buick LaCrosse and Chevy Malibu. The XT5 uses a modified version of the LaCrosse/Malibu platform, so it's possible the XT3 could use a shorter version of the XT5 chassis. Depending on how small the XT3 ends up being, it might even share a platform with the Chevy Trax and Buick Encore. However, considering their economy car roots and torsion-bar rear suspension, we think that's the least likely. Regardless of what chassis is underneath its crisp bodywork, we expect the XT3 to be released sometime next year. Related Video:

GM announces $7 billion Michigan factory investment, most going to EVs

GM announced a $7 billion investment in Michigan manufacturing, much of which is earmarked for EV production. Four sites are included, but the key elements are a new battery cell plant in Lansing and the conversion of GM's existing Orion Township facility to expand production of the forthcoming Chevrolet Silverado EV and its GMC Sierra sibling.  GM says it is the largest investment announcement in company history and that it will create 4,000 new jobs. It also says 1,000 jobs will be retained. "We are building on the positive consumer response and reservations for our recent EV launches and debuts, including the GMC Hummer EV, Cadillac Lyriq, Chevrolet Equinox EV and Chevrolet Silverado EV," said GM CEO Mary Barra.  GM says the Orion expansion and new battery plant will support an increase in full-size electric truck production capacity to 600,000 units. This is in addition to the Factory ZERO facility in Detroit that will also be constructing the electric Silverado and Sierra.  The Orion Township factory current builds the Chevrolet Bolt EV and EUV, and will continue to do so during the plant's conversion. GM did not indicate what will happen with the Bolts once that conversion is complete or whether all will continue to be built at Orion. They do not use the Ultium vehicle architecture. GM will build other EV models at three other factories that are under construction or being converted. They are located in Spring Hill, Tennessee, Ingersoll, Ontario, and Ramos Arizpe, Mexico. GM says that it will have the ability to produce 1 million electric vehicles by 2025. The Ultium Cells Lansing facility is a $2.6 billion joint investment by GM and LG Energy Solution. GM says it alone will create 1,700 jobs once fully operational by late 2024. It will join two other GM Ultium Cells battery factories currently under construction in the United States, one in Ohio and the other in Tennessee.  Not all of the $7 billion investment will be for EVs. It also announced $510 million of the total will go toward upgrading the Lansing Delta Township Assembly to produce the next-generation Chevrolet Traverse and Buick Enclave. Money will also go to upgrading Lansing Grand River Assembly.