1972 Cadillac Eldorado on 2040-cars

Auto blog

GM recalls Cadillac ATS and Chevy Impala for separate issues

The National Highway Traffic Safety Administration added two recalls from General Motors in the government organization's daily update of safety campaigns. Both were for failing to meet Federal Motor Vehicle Safety Standards but for completely separate reasons. The larger recall covers 58,698 units of the 2013-2015 Cadillac ATS, but it doesn't really carry huge safety concerns. In vehicles produced between April 25, 2012, and February 9, 2015, the controls for the tilt and slide of the moonroof are not recessed enough, as required by federal law. According to NHTSA, it's possible that someone could inadvertently activate the auto-close for the roof panel, which the agency claims increases "the risk of personal injury." Dealers will install a new trim plate that will add the necessary clearance. The other campaign covers 1,177 examples of the 2014 Chevrolet Impala from between November 15, 2012, and May 27, 2014. However, this is actually a repeat of a previous recall on the Chevy and the Cadillac XTS from 2014. The affected Impalas here "were remedied incorrectly" under the earlier campaign, according to NHTSA. On these sedans, it's possible the electronic parking brake might not fully disengage and still remain in some contact with the rotor, which is in violation of federal rules. The fault can cause excessive heat from the brakes that could potentially lead to a fire, according to NHTSA. To fix the problem, dealers will reprogram the electronic parking brake control module. Show full PR text RECALL Subject : Inadvertent Press of Roof Panel Switch/FMVSS 118 Report Receipt Date: FEB 24, 2015 NHTSA Campaign Number: 15V106000 Component(s): VISIBILITY Potential Number of Units Affected: 58,698 All Products Associated with this Recall Vehicle Make Model Model Year(s) CADILLAC ATS 2013-2015 Details Manufacturer: General Motors LLC SUMMARY: General Motors LLC (GM) is recalling certain model year 2013-2015 Cadillac ATS vehicles manufactured April 25, 2012, to February 9, 2015. In the affected vehicles, the power-operated roof panels auto-close when the non-recessed "Slide" or "Tilt" switches are pressed. As such, these vehicles fail to comply with the requirements of the Federal Motor Vehicle Safety Standards (FMVSS) No.

Cadillac is returning to endurance racing with a new prototype in 2017

In two months, Cadillac will return to top-tier endurance racing with its all-new Daytona Prototype International racecar after 14 years away. The car, which adheres to IMSA's new DPi regulations, looks as long, low, and Cadillac-like as anyone could have hoped. It's set to debut at the Rolex 24 at Daytona and will compete head to head with the likes of Mazda and Nissan in what is shaping up to be one of the most diverse and exciting forms of American motor racing in years. The new car will be run by Wayne Taylor Racing, the team that previously fielded the Corvette Daytona Prototype. Wayne Taylor himself has won the 24 Hours of Daytona twice, in 1996 and 2005. He now manages the team and leaves the driving duties to his two sons, Ricky and Jordan. They'll be joined in the cockpit by Max Angelelli, Wayne Taylor's teammate in 2002 at Cadillac's last unsuccessful attempt at endurance racing. To understand Cadillac's new car, officially called the DPi-V.R., you need to understand IMSA's DPi category. Basically, manufacturers are allowed to base their car on one of four chassis that follow the FIA LMP2 regulations. The chassis come from either Dallara, Onroak Automotive, ORECA or Riley/Multimatic. Cadillac will base their car on the Dallara platform. The DPi regulation differ from the LMP2 in two major ways: non-standardized engines and the ability to change certain parts of the bodywork. The DPi regulations are intended to give the variety of the top-tier LMP1 cars at a fraction of the cost. When it came to choosing an engine, Cadillac wanted to power the new car with something kinda sorta production based. The new car will use a naturally aspirated 6.2-liter pushrod V8 that shares some base architecture with the engine in the current CTS-V. While the power output hasn't been announced, expect about 600 horsepower. While that's down compared to the CTS-V, there is far less mass to move around as the Dallara chassis is a svelte 2,050 lbs. Since all the teams will be running different engine configurations, expect restrictors of some sort to help balance the power disparity. The parts of the body work that can be modified - The nose, sidepods, rear wheel arches and rear valance - have all been designed to mimic Cadillac roadcar design elements. Even the wheels look like they were pulled straight from the CTS-V. The front splitter, the floor, and the diffuser are common elements shared with other DPi cars.

Cadillac SRX production moving to TN, next-gen Equinox going to Mexico

It's a good week for the town of Spring Hill, TN, as General Motors has announced that its factory in the city of 31,000 will receive a $185 million contract to produce engines. On top of that, the next-generation Cadillac SRX crossover will be built at the factory (NA models are presently built in Ramos, Arizpe Mexico), which was once famous for being the home of GM's now-defunct Saturn brand.
The factory is one of GM's six facilities around the globe that will screw together the company's new line of three- and four-cylinder Ecotec engines. Spring Hill currently builds the 2.0-liter, turbocharged Ecotec, as well as the naturally aspirated 2.4 and 2.5-liter variants.
Spring Hill's vehicle assembly lines were idled in 2009, but were reactivated in 2011. The SRX is just one of the products meant to benefit from last year's $350-million investment, and should have a positive impact, creating or retaining around 1,800 positions at the factory.