2004 Cadillac Deville Pearl White Leather Wood Alloys Low Miles Clean ! on 2040-cars

Auto blog

Online Find Of The Day: 2008 Cadillac XLR picks up where Excalibur left off

We try very, very hard to keep snark away from creations like the one you see here. After all, someone poured plenty of enthusiasm, time and money into turning a 2008 Cadillac XLR into a modern interpretation of the new-old cars typically done by cottage builders like Excalibur and Clénet. Even so, it's hard not to wince when you set an eye on this machine. With its wheelbase stretched to accommodate the extra bodywork, goofy sidewalls and upkicked nose (examine it in profile, it looks slightly bent in the middle), this "neoclassic" takes whatever was loveable about the Cadillac underneath and buries it in a tacky grave.
Miraculously, the engine bay has been left unmolested, which means the retractable hardtop convertible still features a 4.6-liter Northstar V8 engine good for 320 horsepower. If only that were enough to outrun its shame. If, for some reason, you feel like taking this thing home, Harry Kaufmann Motorcars of Milwaukee says it can be yours for a paltry $74,998. We wish were joking. Check it out here.

Akerson says Cadillac will get a larger sedan within two years

It seems that during a recent affair showing off the 2014 Cadillac CTS, General Motors CEO Dan Akerson confirmed reports regarding a new Cadillac flagship sedan. According to USA Today, which Akerson was visiting, he said that a sedan larger than the XTS would debut within the next two years.
This matches up with what we heard earlier in the month about a Cadillac model that will go up against the BMW 7 Series and Mercedes-Benz S-Class (not a pricier, low-volume sedan also discussed in that article). But this is the first time a high-profile executive name has been attributed to such a report, and the first time a broad timeframe has been mentioned. This article adds that the unnamed car will be rear-, and all-wheel drive with a platform "loosely based" on the new CTS, with styling closer to that car than recent Cadillac concept vehicles. The XTS will continue production of course, as well.

[UPDATE] Cadillac Blackwing gets ticket to Italy, to go to work in a supercar

UPDATE: It seems MAT's belief it had secured a supply of Cadillac's 4.2-liter Blackwing V8 was premature, and based on a handshake deal before GM sold its Turin engine center to Italy's Punch Group. Shortly after Hagerty ran the story, GM sent a statement to the outlet reading, in part, "We do not have an agreement in place with Manifattura Automobili Torino (MAT) to provide or sell the Blackwing engine. ... Our team is following up with MAT president Paolo Garella to discuss the misunderstanding." MAT also submitted a statement to Hagerty, saying, in part, "We thank GM for the clarification. Although a signed agreement was not finalized between the parties, we were under the impression that our counterpart was committing to making this engine available to MAT at conditions yet to be defined. ... We hope that this misunderstanding will not compromise our relations with GM and possible future collaborations." The original article follows: Some necessary cost-cutting at Cadillac led to switching the new CT4, CT5, and Escalade to older platforms. The revised architecture plan meant Cadillac's newest top-tier products couldn't fit Cadillac's newest top-tier engine, the 4.2-liter twin-turbo DOHC V8 known as Blackwing. That engine would serve limited duty at full power in the now-dead CT6-V, and at reduced output in the CT6 Platinum V8 trim before ending its bright, brief domestic life. But the story isn't over, the rebirth of Blackwing coming from a most surprising locale: Turin, Italy. Before the canceled Geneva Motor Show, Hagerty spoke to Paolo Garella, CEO of Manifattura Automobili Torino; that's the company better known as MAT, makers of the New Stratos and contract engineering house for boutique screamers like the Aspark Owl electric hypercar, Apollo Intensa Emozione, and SCG003C. Garella told the outlet, "We have an agreement with General Motors" for a supply of Blackwings, which would be developed and built at the General Motors Propulsion Engineering Center (PEC) in Turin. Since 2005, the PEC has been used to develop GM's global diesel engines and electronics. MAT's plan is to put the V8 into a new limited-run car MAT is creating from its own design. Then another surprising turn: Belgium-based global auto supplier Punch Group bought the PEC, with plans to work with GM on projects in progress until at least the end of 2021. Nothing changes as far as MAT is concerned, except perhaps a chance for an even closer collaboration with Punch Turin.