Awd 4dr Suv 4.4l V8 Nav Active Suspension Moonroof on 2040-cars

Auto blog

2016 BMW M3 and M4 recalled for driveshaft problem

The Basics: BMW is recalling 42 examples of the 2015-2016 M3 built from May 30, 2015, to September 2, 2015; the 2016 M4 Coupe made from July 3, 2015, to September 11, 2015; and the 2015-2016 M4 Convertible manufactured from May 29, 2015, to August 4, 2015. The Problem: The company might not have filled a driveshaft slip joint with grease, and the part can potentially fail over time. If this happens, the vehicles could lose power to the rear axle. Injuries/Deaths: None reported. The Fix: BMW dealers will inspect the driveshaft and replace it as necessary. If You Own One: BMW will begin the recall on January 8, 2016. An FAQ (as a PDF) says the vehicles are still safe to drive. More Information: BMW issued two other recalls for similar models this year. An airbag problem prompted a campaign for 2,067 examples of the 4 Series Convertible in March. A fuel pump issue in April also forced repairs to the 3 and 4 Series, in addition to the 2 Series. RECALL Subject : Driveshaft Slip-Joint may not have been Greased Report Receipt Date: NOV 23, 2015 NHTSA Campaign Number: 15V782000 Component(s): POWER TRAIN Potential Number of Units Affected: 42 All Products Associated with this Recall Vehicle Make Model Model Year(s) BMW M3 2015-2016 BMW M4 2015-2016 Details Manufacturer: BMW of North America, LLC SUMMARY: BMW of North America, LLC (BMW) is recalling certain model year 2015-2016 M3 Sedan vehicles manufactured May 30, 2015, to September 2, 2015, 2016 M4 Coupe vehicles manufactured July 3, 2015, to September 11, 2015, and 2015-2016 M4 Convertible vehicles manufactured May 29, 2015, to August 4, 2015. The affected vehicles have a driveshaft with a slip-joint that may not have been filled with grease. As a result, the slip-joint may fail over time. CONSEQUENCE: If the slip-joint fails, there would be a loss of power to the rear axle and therefore the vehicle would stop moving, increasing the risk of a crash. REMEDY: BMW will notify owners, and dealers will inspect the driveshaft, replacing it as necessary, free of charge. The recall is expected to begin January 8, 2016. Owners may contact BMW customer service at 1-800-525-7417. NOTES: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

BMW to announce location of new plant in Mexico in July

Volkswagen manufactures in Mexico. Soon Audi will as well, and Mercedes-Benz is said to be working on a deal to assemble some of its cars at a Nissan plant in Mexico too. That leaves BMW out of the mix of German automakers building cars South of the Border, but that may soon be rectified, as well.
According to Automotive News, the Bavarian automaker is preparing to announce the site of its first Mexican assembly plant as soon as July, now just two months away. BMW already builds cars for North American consumption at its plant in Spartanburg, South Carolina, but has reportedly been keen to capitalize on cheaper labor and the benefits of the North American Free Trade Agreement to supply vehicles to the United States and Canada especially.
When BMW does announce the site of the plant - reportedly narrowed down to either Hidalgo or San Luis Potosi - it is tipped to work its way up to 100,000 vehicles per year at the new location, potentially to include the 3 Series as well as smaller, front-drive models, including Minis.

BMW 1 Series prototype packs direct water injection

Just a few months ago, BMW showcased an M4 that was modified to serve as the safety car for the MotoGP racing series. The flashing lights and emergency equipment, however, weren't the only modifications BMW made to the performance coupe. It also packed an innovative new water injection system. And now it's furthering the development of that system by running it in a 1 Series hatchback as well. Revealed at the BMW Group Innovation Days 2015 event, this five-door 1 Series packs a three-cylinder gasoline engine – like the one found in a Mini or i8 – but fitted with the direct water injection system. In this application, the system sprays a fine mist of water – yep, regular old H2O – right into the combustion chamber. While mixing water with gasoline normally wouldn't be recommended, in this case it evaporates immediately and helps cool the engine from the inside, allowing it to run at higher efficiency. That cooler running engine brings with it several benefits. It delivers improved fuel economy and lower emissions, to start. It also allows for an earlier ignition point, higher compression ratio, and higher boost pressure in turbocharged engines, delivering increased output. It even cuts down on engine knocking (where combustion occurs spontaneously), reduces wear and tear on the engine, and makes better use of lower octane levels. If that sounds like a win-win-win... win (we're losing count of all the wins here), it's because BMW just may be on to something. Of course it does require a water tank to be fitted on board, which means added weight, but instead of requiring the driver fill up the water tank, BMW has fitted this prototype with a system that replenishes the water level from the air conditioning system when the vehicle is switched off. So unless it's being driven in a particularly extreme climate, it doesn't even need topping up. Add one more "win" to the list, then. Extra power, improved real-world fuel economy: Direct water injection enhances efficiency. With direct water injection for turbocharged petrol engines, the BMW Group has again succeeded in enhancing the capabilities of conventional engine technology through an ongoing process of refinement and improvement. The precisely controlled injection of water into the engine cylinders produces a cooling effect that boosts power and torque, particularly when operating at or near full throttle, while at the same time reducing fuel consumption and emissions.