3.0i 6 Speed Manual Leather Heated Seats Low Miles on 2040-cars

Auto blog

Is the skill of rev matching being lost to computers?

If the ability to drive a vehicle equipped with a manual gearbox is becoming a lost art, then the skill of being able to match revs on downshifts is the stuff they would teach at the automotive equivalent of the Shaolin Temple. The usefulness of rev matching in street driving is limited most of the time – aside from sounding cool and impressing your friends. But out on a race track or the occasional fast, windy road, its benefits are abundantly clear. While in motion, the engine speed and wheel speed of a vehicle with a manual transmission are kept in sync when the clutch is engaged (i.e. when the clutch pedal is not being pressed down). However, when changing gear, that mechanical link is severed briefly, and the synchronization between the motor and wheels is broken. When upshifting during acceleration, this isn't much of an issue, as there's typically not a huge disparity between engine speed and wheel speed as a car accelerates. Rev-matching downshifts is the stuff they would teach at the automotive equivalent of the Shaolin Temple. But when slowing down and downshifting – as you might do when approaching a corner at a high rate of speed – that gap of time caused by the disengagement of the clutch from the engine causes the revs to drop. Without bringing up the revs somehow to help the engine speed match the wheel speed in the gear you're about to use, you'll typically get a sudden jolt when re-engaging the clutch as physics brings everything back into sync. That jolt can be a big problem when you're moving along swiftly, causing instability or even a loss of traction, particularly in rear-wheel-drive cars. So the point of rev matching is to blip the throttle simultaneously as you downshift gears in order to bring the engine speed to a closer match with the wheel speed before you re-engage the clutch in that lower gear, in turn providing a much smoother downshift. When braking is thrown in, you get heel-toe downshifting, which involves some dexterity to use all three pedals at the same time with just two feet – clutch in, slow the car while revving, clutch out. However, even if you're aware of heel-toe technique and the basic elements of how to perform a rev match, perfecting it to the point of making it useful can be difficult.

Mini Cooper SE Convertible wheels made entirely from recycled aluminum

Mini has revealed an interesting fact about its limited-run Mini Cooper SE Convertible: It's the first production car with wheels made from 100% recycled aluminum. Despite sharing the same look as wheels available on the regular SE hatch, they're actually much more environmentally friendly. The wheels were developed with Swiss wheel manufacturer Ronal. The company sells aftermarket wheels under the Ronal and Speedline brands, and it supplies OEMs. And it's no stranger to more environmentally-friendly wheel production. It supplies wheels for the Audi E-Tron GT that are made using a smelting process that produces oxygen rather than carbon dioxide, and it now has a line of claimed carbon-neutral aftermarket wheels. But back to the Mini's wheels. Using all recycled aluminum has the obvious benefit of not requiring new aluminum to be manufactured. But the benefits are greater than just the raw material use. Mini points out that a major improvement in carbon emissions comes from being able to skip the electrolysis process for new aluminum manufacturing. Pure aluminum is extracted from aluminum oxide (which is in turn taken from the mineral bauxite). To do this large amounts of electricity are passed through molten solutions of aluminum oxide and cryolite (which takes energy to heat) across graphite cathodes and annodes. Not only does this use a lot of electricity that has its own carbon costs, the oxygen that separates from the aluminum bonds to the graphite annodes, yielding more carbon dioxide (which is why the production of those Audi wheels is also interesting). In total, Mini says the recycled wheel production reduces carbon emissions by 75%. More specifically, it estimates about 0.16 kilograms (0.35 pounds) per kilogram (2.2 pounds) of aluminum used. Mini also stresses that this process still maintains all the strength of conventional wheels, just in a greener way. And of course, the wheels themselves are recyclable again. Mini, and BMW more broadly, are looking at ways to upscale the process and to source suitable recyclable products, likely other old wheels from cars no longer on the road. Though neither company said anything about when we'll see fully recycled wheels more widely available. Related Video: MINI Electric Pacesetter inside and out

Mini JCW Paceman vs. BMW M135i in family faceoff

Over the last year, we've had the chance to drive two of the most exciting hatchbacks in the BMW family - the BMW M135i and the Mini Paceman John Cooper Works - but Autocar has managed to get the two corporate cousins together for a head-to-head comparison. Just like our initial impressions of the Paceman JCW, Autocar has little to complain about this new 215-horsepower hatchback... until it begins to factor in the faster, better-mannered and similarly priced M135i.
Despite laying down an extra 100 hp and delivering a 0-60 time that is almost two seconds quicker, the M135i carries the same price tag of 29,535 pounds in the UK; US pricing for the Paceman starts at $36,200, while it still isn't even clear if the US will be getting the M135i. Even more surprising is the fact that the Paceman falls short of the M135i in regards to rear seat and cargo volume, and just barely squeaks out a win in the fuel economy department. Scroll down to watch the BMW versus Mini hot hatch battle.