Convertible White/beige Premium Package Real Leather Interior Ipod Connector Cab on 2040-cars

Auto blog

Is the skill of rev matching being lost to computers?

If the ability to drive a vehicle equipped with a manual gearbox is becoming a lost art, then the skill of being able to match revs on downshifts is the stuff they would teach at the automotive equivalent of the Shaolin Temple. The usefulness of rev matching in street driving is limited most of the time – aside from sounding cool and impressing your friends. But out on a race track or the occasional fast, windy road, its benefits are abundantly clear. While in motion, the engine speed and wheel speed of a vehicle with a manual transmission are kept in sync when the clutch is engaged (i.e. when the clutch pedal is not being pressed down). However, when changing gear, that mechanical link is severed briefly, and the synchronization between the motor and wheels is broken. When upshifting during acceleration, this isn't much of an issue, as there's typically not a huge disparity between engine speed and wheel speed as a car accelerates. Rev-matching downshifts is the stuff they would teach at the automotive equivalent of the Shaolin Temple. But when slowing down and downshifting – as you might do when approaching a corner at a high rate of speed – that gap of time caused by the disengagement of the clutch from the engine causes the revs to drop. Without bringing up the revs somehow to help the engine speed match the wheel speed in the gear you're about to use, you'll typically get a sudden jolt when re-engaging the clutch as physics brings everything back into sync. That jolt can be a big problem when you're moving along swiftly, causing instability or even a loss of traction, particularly in rear-wheel-drive cars. So the point of rev matching is to blip the throttle simultaneously as you downshift gears in order to bring the engine speed to a closer match with the wheel speed before you re-engage the clutch in that lower gear, in turn providing a much smoother downshift. When braking is thrown in, you get heel-toe downshifting, which involves some dexterity to use all three pedals at the same time with just two feet – clutch in, slow the car while revving, clutch out. However, even if you're aware of heel-toe technique and the basic elements of how to perform a rev match, perfecting it to the point of making it useful can be difficult.

2016 BMW M4 GTS: More power, less weight, ready for the track

BMW calls its new M4 GTS the "most agile, radical, and powerful M4 ever." It's got 493 horsepower, a slick new water injection system, a three-way adjustable coilover suspension, and a weight reduction of roughly 200 pounds compared to a stock M4. Only 700 will be built, with 300 allocated for the United States. And did we mention it looks absolutely killer? Let's talk about that water injection system for a moment, because it's the first time this technology is being used on [an intercooled - Ed.] production road car. Basically, water absorbs heat from surrounding air, so a fine mist is sprayed into the intake manifold where it evaporates, lowering the temperature of the intake air. BMW says this reduces final compression temperature, allowing the turbochargers to operate with increased boost pressure and better spark timing. The end result is increased output – 493 horsepower and 442 pound-feet of torque from the same twin-turbo, 3.0-liter straight-six as the standard M4. That's an increase of 68 hp and 36 lb-ft. But the GTS isn't just about increased power. In fact, the bigger story is its weight reduction. BMW incorporated the use of aluminum and carbon fiber throughout the M4's construction, and DIN curb weight is listed as 3,329 pounds. It's unclear if that's the exact US measurement, and BMW couldn't comment on that as of this writing, but compared to our 3,530-pound stock M4, that represents some 200 fewer pounds of heft. Carbon fiber reinforced plastic (CFRP) is used in the hood, making that part some 25 percent lighter than the stock piece. CFRP is also used for the driveshaft, making it 40-percent lighter than the standard setup. Even inside the car, the new center console is 30-percent lighter than what you'd find in a normal M4. The rear seats are gone, and we're sorry to say that the cool racing buckets pictured here won't be available in the US. Making this thing super capable at the track is a three-way M coilover suspension, combined with upgraded carbon ceramic brakes, set behind staggered wheels and tires. Up front, the GTS rides on 19-inch rollers wrapped in 265/35-series Michelin Pilot Sport Cup 2 tires, and out back, 20-inch wheels are fitted inside 285/30-series rubber. The only transmission available is the seven-speed, M DCT dual-clutch unit, and when all is said in done, BMW says the M4 GTS will run the infamous Nurburgring Nordschleife in 7 minutes and 28 seconds. Another cool feature: organic LED technology.

Excavator in China bashes BMW and Jeep out of the way

This Chinese construction site apparently has a zero tolerance policy towards obstacles getting in the way of work. When blocked by a Jeep and a BMW, the operator of this excavator pushes the two vehicles out of the way like they're toys. The Bimmer gets the brunt of the abuse, with the sedan getting lodged up against a fence. The exact context of this clip isn't entirely known, but The Mirror in Britain speculates the vehicles are illegally parked. But that doesn't explain why the excavator crashes through a gate later in the video. Also, this doesn't appear to be the case of a rogue operator taking out some frustrations, because a man with a walkie-talkie is leading the way and seemingly directing the destruction. Nonetheless, getting permission to knock these cars around was probably the highlight of this driver's day. News Source: The Mirror, AOL On BMW Jeep Crossover Videos Sedan