128i Convertible 3.0l Cd Keyless Start Traction Control Stability Control Abs on 2040-cars

Auto blog

2016 BMW 7 Series slims down, techs up

BMW is finally pulling the wraps off its sixth-generation 7 Series. The flagship boasts a ton of improvements for 2016, including a smattering of onboard tech and weight reduction of 190 pounds. The 7 Series uses a new internal structure called Carbon Core. Derived from the i sub-brand, Carbon Core uses a mix of carbon-fiber-reinforced plastic and ultra-high-tensile steel for the 7's major structural components. It's largely responsible for the 190-pound weight reduction, along with the aluminum doors and trunk lid. The weight savings has allowed BMW to maintain a fifty-fifty weight distribution. That new structure underpins the largest sedan BMW has ever produced. At 206.6 inches in total, the long-wheelbase-only 7 Series is over an inch longer than its predecessor. Its 124.6-inch wheelbase and 74.9-inch width, though, remain unchanged. Even with such a modest increase in size, BMW is claiming best-in-class rear legroom, at 44.4 inches – a tenth of an inch more than the current 7. Unlike the old car, though, this new 7 Series gets with the times in terms of chauffeur equipment. The front passenger seat can be slid forward and folded, allowing a lucky rear passenger to take advantage of the new pop-out footrest and optional 42.5-degree seat incline, available as part of the Rear Executive Lounge Seating Package. iDrive now adds a number of 3D sensors that respond to pre-programed hand motions. The 7 Series will debut here in the United States with two engines, both of which should be familiar to BMW consumers. There's a 320-horsepower, 3.0-liter, turbocharged six-cylinder in the nose of the 740i, and a 4.4-liter, twin-turbocharged V8 with 445 hp on tap in the 750i xDrive. 60 miles per hour arrives in a relaxed 5.4 seconds for the 740i and 4.3 seconds in the V8 model. Once again, ZF provides the eight-speed automatic transmission used with both engines. Joining the 740i and 750i is the new 740e xDrive. The plug-in-hybrid sedan is motivated by a 2.0-liter, turbocharged four-cylinder and an electric motor, and is capable of 23 miles per charge and speeds of up to 75 miles per hour in pure electric mode. Tthere's no shortage of tech on the latest 7 Series. While we're familiar with some items, like active grille shutters and BMW's Air Breather system, it's items like the gesture-control-equipped iDrive 5.0 that pique our interest. Alongside the new and standard touchscreen, iDrive now adds a number of 3D sensors that respond to pre-programed hand motions.

BMW recalls diesel X5 models over fuel filter heater

BMW has announced that it is recalling 1,540 examples of its 2009 and 2010 X5 xDrive35d crossovers produced between June 13, 2009 and November 9, 2009.
According to the National Highway Traffic Safety Administration, the model's fuel filter heater, which warms up the diesel fuel at low outside temperatures, can experience an electrical overload condition that may cause it to become permanently activated. This means the fuel filter heater could remain activated even when the ignition is off, which could lead to a dead battery. It could also lead to overheating, possibly resulting in a fire.

New BMW i3-like Visio.M EV concept uses lightweight resin

It's not a new version of the BMW i3, but an updated version of a lightweight concept car from SABIC, BMW, the Technical University of Munich, Daimler and others does bear a certain resemblance to the well-designed plug-in city car. From the black "glass" in the hatch to the angled line tail lights to the up-and-down window line, you can see a sort of family resemblance (see an i3 comparison photo here). And, of course, they both have an electric powertrain. But the changes made to the new lightweight urban electric concept vehicle is more of an exercise in what's possible rather than a way to evolve the i3 and i8 into a broader i family of vehicles. Even so, what we see here is interesting, since SABIC found all sorts of new ways to take weight out of the car as part of the Visio.M (Visionary Mobility) project, which was first announced in 2012. Let's start with the window material, which as you might guess from the quotation marks above, is not made of glass but is instead SABIC's Lexan polycarbonate (PC) resin plastic. The lower weight (the PC helps shed about 29 pounds) adds two miles of range while the PC resin has better thermal conductivity compared to glass and so does even more because the HVAC system can be more efficient. According to SABIC's computational fluid dynamics analysis, an extra 9-10 miles of range, in fact. Without the battery, this concept weighs just 992 pounds. Remember, BMW already made a lot of weight-reduction measures in the i3 thanks to carbon fiber reinforced plastic, so to make the "glass" lighter would only help boost efficiencies on a production vehicle that uses a resin like this. Read more below. SABIC's LEXAN™ resin delivers weight savings and thermal efficiency for new ultra-lightweight electric car concept developed by BMW-led Visio.M Consortium Munich, October 20, 2014 Today, at the Technical University of Munich (TUM), BMW, Daimler, TUM scientists and a consortium of industry participants showcased a lightweight urban electric concept vehicle with various advances, including an all-plastic design of the car's windows. The windows are made of LEXAN resin, a polycarbonate (PC) material, and coating technologies from SABIC, a leading developer of PC glazing for automotive windows and many other thermoplastic solutions for the automotive industry.