2007 Audi Q-7 3.6 Quattro, Pano Roof,s-line Sport,20 Wheels, Nav, Keyless Go on 2040-cars

Auto blog

2014-15 Audi SQ5 recalled for steering issue

Audi is recalling 5,625 SQ5 crossovers from model years 2014 and 2015 due to a fault in the electric power-assisted steering system. The affected vehicles were built between May 22, 2013 and April 14, 2015. The vehicles in question may experience power-steering shutdowns in cold conditions. Good thing the US' average July temperature sits in the mid 70s. The actual root of the problem is a fault in the steering motor sensor, according to the bulletin from the National Highway Traffic Safety Administration. While manual steering would still be available, the sudden loss of power could catch drivers off guard, increasing the chances of a crash. Owners of the affected vehicles will be notified by Audi USA, and will need to report into dealers for a software update to the power steering control module. Scroll on down for the official notification from Audi. Report Receipt Date: JUL 20, 2015 NHTSA Campaign Number: 15V452000 Component(s): STEERING Potential Number of Units Affected: 5,625 Manufacturer: Volkswagen Group of America, Inc. SUMMARY: Volkswagen Group of America, Inc. (Volkswagen) is recalling certain model year 2014-2015 Audi SQ5 vehicles manufactured May 22, 2013, to April 14, 2015. The affected vehicles have an electric power steering assist system that may shut down in cold temperatures due to a steering motor sensor fault. CONSEQUENCE: If the vehicle experiences a loss of power steering assist, extra steering effort will be required at lower speeds, increasing the risk of a vehicle crash. REMEDY: Volkswagen will notify owners, and dealers will update the power steering control module software, free of charge. The recall is expected to begin July 28, 2015. Owners may contact Audi customer service at 1-800-253-2834. Volkswagen's number for this recall is 48M1. NOTES: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Here’s how 20 popular EVs fared in cold-weather testing in Norway

Electric vehicles are known to suffer diminished performance in cold weather, but some do a better job than others hanging onto their range capacity while cabin heaters and frigid outdoor temperatures sap power from their batteries. Recently, the Norwegian Automobile Federation put the 20 of the best-selling battery-electric vehicles in the country to the test, to see not only how winter weather affected their range but also their charging times. The major findings: On average, electric vehicles lost 18.5% of their official driving range as determined by the European WLTP cycle. Electric vehicles also charge more slowly in cold temperatures. And interestingly, the researchers learned that EVs don’t simply shut down when they lose power but instead deliver a series of warnings to the driver, with driving comfort and speed levels maintained until the very last few miles. Because itÂ’s Norway, the worldÂ’s top market for electric and plug-in hybrid vehicles by market share, the test included many EVs that arenÂ’t available here in the U.S. But there are many familiar faces, among them the Nissan Leaf, Tesla Models S, 3 and X, Hyundai Kona (known here as the Kona Electric) and Ioniq, and Audi E-Tron. In terms of range, the top-performing EV was the Hyundai Kona, which lost only 9% of its official range, which the WTLP rated at 449 kilometers, or 279 miles, compared to its EPA-rated range of 258 miles on a full charge. It delivered 405 km, just enough to nudge it ahead of the Tesla Model 3, which returned 404 km. Other top performers included the Audi E-Tron, in both its 50 Quattro (13% lower range) and higher-powered 55 Quattro (14% lower) guises; the Hyundai Ioniq (10% lower); and Volkswagen e-Golf (11% lower). At 610 km (379 miles) the Tesla Model S has the longest WLTP range of all models tested and went the furthest, but still lost 23% of its range, though it also encountered energy-sapping heavy snow at the end of its test, when many cars had dropped out. The Model 3 lost 28% of its range. The worst performer? That goes to the Opel Ampera-e, better known stateside as the Chevrolet Bolt. It traveled 297 km (about 184 miles) in the test, which was nearly 30% lower than its stated WLTP range. We should also note that Opel, now owned by Groupe PSA, is phasing the car out in Europe and that Chevy recently upgraded the Bolt here in the U.S.

Audi 3D-printed this tiny Type C racer, we want to drive it

See this little guy? No, not the one driving – that's Professor Hubert Waltl, Audi's head of production and Volkswagen's chief toolmaker. The thing he's driving, though, is a 1:2 scale replica of the 1936 Auto Union Type C. And it was 3D-printed entirely in house. Not in one piece, mind you. It's too big for that. But the Audi Toolmaking division employed metal printing technology to fabricate all the parts that went into this replica of one of the most dominant of the Silver Arrow grand prix racers of the pre-war era. It's essentially like the pedal car Audi rolled out nine years ago, or the E-Tron concept it showed us nearly five years ago. Only this one uses more advanced manufacturing techniques. Aside from making us want to drive it like nobody's business, the half-sized vehicle serves to showcase the advancements which Audi and the VW Group are making in manufacturing – particularly in the area of 3D printing. The German automaker presently has the technology to print laser-melted layers of metallic powder – either steel or aluminum – with grains measuring half the diameter of a human hair. The equipment can handle objects as large as 7.9 inches high by 9.5 inches wide – which, as small as this little car looks, is still a bit too large to simply print out in one piece. Audi Toolmaking prints "Auto Union Typ C" - Exact model of the "Silver Arrow" from a 3D printer - Audi Board of Management Member for Production Prof. Dr. Hubert Waltl: "This underscores our pioneering role in toolmaking." From powder to a component: With a 3D printer, Audi Toolmaking has produced a model of the historical Grand Prix sports car "Auto Union Typ C" from the year 1936. The company is now examining further possible applications of metal printers for the production of complex components. At the same time, Audi is creating important synergies with toolmaking in other parts of the Volkswagen Group. "We are pushing forward with new manufacturing technologies at Audi Toolmaking and at the Volkswagen Group," stated Prof. Dr. Hubert Waltl, Audi's Board of Management Member for Production and Head of Toolmaking at the Volkswagen Group. "Together with partners in the area of research, we are constantly exploring the boundaries of new processes. One of our goals is to apply metal printers in series production." The Volkswagen Group has a total of 14 toolmaking units in nine countries. Under the leadership of Prof. Dr.