2001 Acura Tl V6 on 2040-cars

Auto blog

2019 Acura RDX crossover gets turbocharged power, A-Spec version

NEW YORK — Calling the RDX that Acura showed at this year's Detroit Auto Show a "concept" was stretching that term to the limits of credulity. The production version of the 2019 RDX is here, and this turbocharged crossover with available AWD looks darn near identical. While it offers all-wheel drive like its Lexus NX and Audi Q3 competitors, Acura's next-generation SH-AWD should be a serious selling point. Let's cover that "Super Handling All-Wheel Drive" system for a moment. It takes power from the 2.0-liter, 272 horsepower and 280 pound-feet of torque engine and routes it up to 70 percent rearward, and there's real torque vectoring (rather than brake-based faux vectoring) to shift 100 percent of that rear axle power to either wheel. The broad strokes are similar to the outgoing model's system, but there's much more available rear power bias — in the 2016 model, up to 40 percent could be sent to the rear. And that was up from 25 percent for pre-2016 models. The takeaway is that the RDX should handle a lot better on both dry and slippery pavement, and feel a bit sportier doing it. A new engine may help as well. The outgoing 3.5-liter V6 is replaced by a turbocharged four-cylinder, almost certainly related to the unit in the Accord and Civic Type R, and tuned somewhere in between those cars (252 and 306 horsepower, respectively). We expect the new engine to be lighter than the old V6, and less weight off the front end should improve steering feel and handling. For those keeping track, the new engine is down 7 horsepower but up 28 pound-feet in torque, and thanks to turbocharging the torque band starts down low and is relatively flat, so more oomph from a stop and on through the rev range. The six-speed automatic is gone, replaced by a 10-speed automatic. Most of its competitors use six- or eight-speed units, so that'll be a marketing focus. As you'd expect, the individual ratios are closer-spaced but the total ratio spread is, according to Acura, 62 percent wider than the outgoing automatic. There are steering-wheel-mounted paddles if you'd like to shift yourself. Since the styling is very much a lightly retouched Prototype RDX from the Detroit show, it's nice to be able to give a sense of the new car's proportions with hard numbers. First of all, it's riding on a 2.6-inch longer wheelbase. Overall length is 187 inches, up from 184.4, and width is unspecified.

Acura NSX production delayed

Listeners of the Autoblog Podcast will be familiar with my opinions on the Acura NSX. While I love the idea of Acura building a halo car again, I've routinely joked on-air that the car will never, ever reach production and will continue being teased and previewed ad nauseam. So I'm chuckling at this news: the NSX is being delayed again. To be fair, while it sounds like a big deal – pushing the NSX back from model year 2016 to 2017 – this is a fairly minor delay in the grand scheme. Instead of starting production this fall, as previously announced, the new supercar will start rolling down the line at Honda's Marysville, OH factory in the spring. "Trial production" has already started, Honda says, while briefly acknowledging the delay in the attached press release. While Honda offered no reason for the delay in volume production, Automobile claims it's the fault of the move to fit two turbochargers to the V6, which was made midway through development. Fitting the two iron lungs meant rearranging the six-pot into a longitudinal layout. Here's hoping there are no further delays. Scroll on for a look at Honda's press release, which does its best to gloss over the NSX delay while talking about the company's new Performance Manufacturing Center in Marysville. Related Video: Performance Manufacturing Center: Precision Craftsmanship Aug 14, 2015 - CARMEL-BY-THE-SEA, Calif. The next-generation Acura NSX is produced at the new, dedicated Performance Manufacturing Center (PMC) in Marysville, Ohio, using domestic and globally sourced parts. With trial production already underway and production start-up scheduled for spring 2016, this world-class manufacturing facility employs groundbreaking techniques in weld, body construction, body painting, final assembly and quality confirmation to ensure the highest levels of precision and craftsmanship. More details on the unique and innovative manufacturing processes at the PMC will be rolled out over the months leading up to the start of production, but the following highlights of the new facility were shared during the 2015 Monterey Automotive Week: Innovative blend of people and technology: throughout the PMC, NSX production is centered around the skills of approximately 100 experienced engineers and technicians building the NSX to precise levels of quality and craftsmanship.

NHTSA gives okay for three automakers to skirt tire-related recalls

BMW, Honda, and Mercedes-Benz are all going to avoid small recalls, after the National Highway Traffic Safety Administration issued petitions for "findings of inconsequential noncompliance" to the three manufacturers, according to Tire Business. Basically, the petitions allow the brands to avoid recalls for some very, very minor issues.
BMW had tire placards on 364 X6 M CUVs that stated the car could only handle four passengers, when in reality it had room for three in the back. Actual plausibility of fitting three real humans in the slope-roofed Bimmer aside, the Munich-based manufacturer argued it was inconsequential, as the placards were correct regardless of the number of passengers.
Honda's case focused on 212 2011 and 2012 Acura TSX sedans equipped with 18-inch wheels. The TPMS systems on these cars were set for 17-inch wheels, rather than the larger hoops, but even with the lower settings, the tires maintain adequate load capacity.