2014 Toyota Sienna Xle on 2040-cars

Auto blog

How Toyota's 100-year textile history influenced FCV hydrogen fuel cell car

Turns out, Toyota had a surprising ace in the hole when it came to building the new fuel tanks for the FCV hydrogen fuel cell car, which is coming next year. Well before Toyota became the Toyota Motor Company, it was the Toyota Industries Corporation and it made textile looms. This is important because the main structure of the hydrogen tank is wound carbon fiber. When Toyota set out to increase the strength of the tanks to hold hydrogen stored at 10,000 psi (up from 5,000 in the previous tanks), it was able to draw on its 100-year-old history as it designed its car of the future. "A lot of that textile experience came back when we did the tank wrapping." – Justin Ward "We have a lot of experience with textiles," Justin Ward told AutoblogGreen at the 21st World Congress on Intelligent Transport Systems (ITS) in Detroit this week, "and a lot of that textile experience came back when we did the tank wrapping." On top of being able to hold the higher-pressure hydrogen, Toyota's first attempt to build its own hydrogen tank was six times faster than the industry standard, so it saved time and money as well as working better. The company will also be able to inspect its own tanks. Ward is the general manager of powertrain system control at the Toyota Technical Center and hydrogen vehicles are something he knows a lot about. The reason for the stronger, 10,000-psi tanks is because the 5,000-psi tanks only offered around 180-200 miles of range, even with four tanks in the early $129,000 FCHV Highlander hydrogen prototypes. The FCV only has two, but they will able to deliver the 300-mile range that customers told Toyota they wanted. Dropping the number of tanks not only obviously reduced the cost for the tanks themselves but also the number of valves and hoses and other components you need. Despite the benefits of higher compression, going much higher doesn't make sense. 10,000 psi is the "natural progression," Ward said, because "you start to bump up against compression inefficiencies." Think of an air compressor. When hydrogen is produced at a wastewater treatment plant or a reforming site, Ward said, is it at around ambient pressure (14 psi). That has to be raised, using compressors, all the way to 10,000 psi. "That takes energy," Ward said, "and every doubling of pressure adds another doubling of energy needed, so it starts to add up pretty fast if you go too high." Component specifications are also fine at 10,00 psi, but more difficult at higher levels.

Japan carmakers vouch for safety of some Kobe Steel parts

TOKYO — Four Japanese automakers on Thursday said they found no safety issues with aluminum parts supplied by Kobe Steel Ltd, allaying some concerns that falsified quality data on products from the steelmaker had compromised their vehicles. Kobe Steel shares surged after the car makers' statements, but the steelmaker still has to contend with a U.S. Justice Department probe, while checks continue at hundreds of companies involved in complex supply chains spanning the globe. Japan's third-biggest steelmaker admitted earlier this month it falsified specifications on the strength and durability of aluminum, copper and steel products, along with materials for optical disks. The falsifications stretch back for more than 10 years, a senior executive told Reuters this week. Since then, global automakers, aircraft companies and other manufacturers have scrambled to identify potential hazards in their products. Toyota, Honda, Nissan and Mazda said that hoods and other exterior parts used in their cars which were made from aluminum directly supplied by Kobe Steel were safe. Kobe Steel shares ended the day nearly 7 percent higher but are still down by more than a third since it announced the data falsification. Automakers are still making checks on other parts, including those that they received through their parts suppliers. "We confirmed that the materials satisfy applicable statutory standards, and our own internal standard, for key safety and durability requirements for vehicles," Toyota said in a statement. Toyota, one of the world's largest automakers, identified aluminum plates supplied by Kobe Steel for the hoods and rear hatches of Toyota and Lexus brand vehicles. Though outside the automaker's specifications, they were still safe to use. While Subaru and other carmakers said they were still investigating the issue, the announcements by Toyota, Honda, Nissan and Mazda suggest that Kobe Steel's cheating scandal may have a limited impact on product safety."SERIOUS SITUATION" Nonetheless, the company's fate hangs in the balance while checks are being carried out. It must report to Japan's industry ministry by around the end of next week on any safety concerns and provide a more extensive account of the problems a fortnight later. Industry leaders have reached a consensus that Kobe Steel is in a "serious situation," a senior Japanese manufacturing executive told Reuters.

Autoblog Podcast #318

Toyota back on top, Barrett Jackson, Crowdsourcing your Dodge Dart payments, Nissan and Toyota double down on pickups
Episode #318 of the Autoblog Podcast is here, and this week, Dan Roth, Zach Bowman and Michael Harley talk about Toyota regaining the No. 1 sales crown, getting your friends and family to buy you a Dodge Dart, Barrett-Jackson, and Toyota and Nissan remaining committed to their pickup trucs. We wrap with your questions, and for those of you who hung with us live on our UStream channel, thanks for taking the time. Keep reading for our Q&A module for you to scroll through and follow along, too. Thanks for listening!
Autoblog Podcast #318: