2011 Toyota Rav4 Sport on 2040-cars

Auto blog

Toyota develops new pre-collision system with steering assist

A number of automakers are working on developing fully autonomous cars, but it looks like the groundwork for such technologies will likely show up first as semi-autonomous systems for both safety and convenience. Following recent announcements from Nissan and Ford in this area, Toyota has now released information for some of its advanced semi-autonomous technologies that could be offered in production cars over the next few years.
On the safety front, Toyota's new pre-collision system with pedestrian-avoidance steering assist is aimed at protecting the folks who aren't in the car. This system combines visual and audible alerts with automatic brake assist and automatic steering. If warnings don't get the driver to slow down, the brake assist kicks in if a collision is very likely, but if that is still not able to avoid the impending collision (and if there is enough room to do so), the car can automatically steer itself around the pedestrian. This sounds most beneficial for last-second dangers such as a person accidently stepping out into the road in front of a car. Toyota hopes to have this technology available to customers by 2015.
The Japanese automaker is also testing a suite of technologies called Automated Highway Driving Assist (AHDA). The key part of this is a new adaptive cruise control system that uses vehicle-to-vehicle (V2V) communications rather than a radar-based system. This cooperative-adaptive cruise control allows vehicles to communicate their acceleration and deceleration data with other cars, which Toyota says this helps to improve fuel efficiency and traffic flow. Also a part of AHDA is the Lane Trace Control feature, which sounds like a next-gen lane keep assist. This system uses cameras, radar and a computer to keep the vehicle in a "smooth driving line" by being able to change steering angle, engine torque and braking force. Toyota says this technology could be in place by the "mid-2010s."

How Toyota's 100-year textile history influenced FCV hydrogen fuel cell car

Turns out, Toyota had a surprising ace in the hole when it came to building the new fuel tanks for the FCV hydrogen fuel cell car, which is coming next year. Well before Toyota became the Toyota Motor Company, it was the Toyota Industries Corporation and it made textile looms. This is important because the main structure of the hydrogen tank is wound carbon fiber. When Toyota set out to increase the strength of the tanks to hold hydrogen stored at 10,000 psi (up from 5,000 in the previous tanks), it was able to draw on its 100-year-old history as it designed its car of the future. "A lot of that textile experience came back when we did the tank wrapping." – Justin Ward "We have a lot of experience with textiles," Justin Ward told AutoblogGreen at the 21st World Congress on Intelligent Transport Systems (ITS) in Detroit this week, "and a lot of that textile experience came back when we did the tank wrapping." On top of being able to hold the higher-pressure hydrogen, Toyota's first attempt to build its own hydrogen tank was six times faster than the industry standard, so it saved time and money as well as working better. The company will also be able to inspect its own tanks. Ward is the general manager of powertrain system control at the Toyota Technical Center and hydrogen vehicles are something he knows a lot about. The reason for the stronger, 10,000-psi tanks is because the 5,000-psi tanks only offered around 180-200 miles of range, even with four tanks in the early $129,000 FCHV Highlander hydrogen prototypes. The FCV only has two, but they will able to deliver the 300-mile range that customers told Toyota they wanted. Dropping the number of tanks not only obviously reduced the cost for the tanks themselves but also the number of valves and hoses and other components you need. Despite the benefits of higher compression, going much higher doesn't make sense. 10,000 psi is the "natural progression," Ward said, because "you start to bump up against compression inefficiencies." Think of an air compressor. When hydrogen is produced at a wastewater treatment plant or a reforming site, Ward said, is it at around ambient pressure (14 psi). That has to be raised, using compressors, all the way to 10,000 psi. "That takes energy," Ward said, "and every doubling of pressure adds another doubling of energy needed, so it starts to add up pretty fast if you go too high." Component specifications are also fine at 10,00 psi, but more difficult at higher levels.

Toyota/Mazda factory will reportedly be in Alabama or North Carolina

The Toyota/Mazda factory sweepstakes appear to be nearing a conclusion as Bloomberg and Automotive News are reporting the location has been narrowed down to either North Carolina or Alabama. The joint venture plant worth $1.6 billion would add 4,000 jobs to whichever state lands it. To even be considered, Toyota and Mazda have reportedly sought a $1 billion incentive package from interested states in the form of tax breaks and other support. At least 15 states had apparently been jockeying for the factory, including Mississippi, Illinois, Michigan, Ohio, Indiana, Texas and South Carolina. Toyota presently has an engine factory near Huntsville, Ala. The state is also currently home to Honda, Hyundai and Mercedes-Benz assembly plants. North Carolina currently does not have a car manufacturing plant. This would also represent Mazda's return to American manufacturing, as its present lineup of cars and crossovers is produced in Japan. The company had previously built cars in the United States along with its former partner Ford. Related Video: